User manual TANDBERG SLR AUTOLOADER SERVICE AND REPAIR MANUAL

[. . . ] TANDBERG SLR AUTOLOADER SERVICE AND REPAIR MANUAL TANDBERG DATA ASA P. O. Box 134 Kjelsås N-0411 OSLO, NORWAY Phone + 47 22 18 90 90 Telefax + 47 22 18 95 50 © Tandberg Data ASA Part No. 43 20 72 ­ 03 December 2003 Related publications available from our Marketing Department: Part No. Title 43 21 77 ­ 03 43 20 73 ­ 03 43 20 74 ­ 01 43 04 44 - 11 43 07 43 - 13 Tandberg SLR Autoloader Installation and User Manual Tandberg SLR Autoloader SCSI Interface Manual Tandberg SLR Autoloader Product Verification Report Tandberg SLR 7-140 Tape Drive Product Reference Manual Tandberg SLR 7-140 Tape Drive Programmers Reference Manual This publication may describe designs for which patents are granted or pending. [. . . ] Zero Based indicates that the elements begin at 0 (Drive 0 and Slots 0 through 7). This value affects only the front panel display. Tandberg SLR Autoloader Service and Repair Manual 42 Tandberg Data Chapter 4 - Configuration Auto Clean Mode -- Enables AutoClean Mode. This option does not display unless you have selected a cleaning slot. Loader Mode -- Allows the loader to be used as either a random access device or as a sequential loader device. When set to Random, the host has full control over the movement of cartridges. Tandberg SLR Autoloader Service and Repair Manual 43 Sequential Mode -- Applies when the Loader Mode is set to Sequential. When Normal is selected, sequential operation terminates after the last cartridge in the sequence has been unloaded. A cartridge sequence ends at an empty slot or when the cartridge in slot 8 has been unloaded. (Slot 7 if Cleaning Slot is enabled) When Recirculate is selected, operation continues with the first cartridge in the sequence. This option does not display unless you have selected Sequential Mode in the Loader Mode option. Baud Rate -- Sets the trace serial port baud rate. Allowable values are: · · · · · · 2, 400 9, 600 19, 200 38, 400 57, 600 115, 200 (Default). Enable Bar Code -- Enables the bar code reader. When the reader is enabled, the barcode of the cartridge in each occupied magazine slot and in the drive (if any) will be scanned during the Inventory process. Enable Check Char -- Enables the check sum character to be used to verify the correctness of each bar code label scan. Does not display unless you have enabled the bar code reader in the Enable Bar Code option. Cleaning Slot -- If enabled, dedicates slot 8 to cleaning operations. Note: Do not insert the cleaning cartridge in any other slot than slot 8. Set Serial Number -- The 12-character string of the assigned serial number entered using the control panel and buttons. Tandberg SLR Autoloader Service and Repair Manual 44 Tandberg Data Chapter 4 - Configuration SCSI Options Loader SCSI ID -- Sets the SCSI ID of the loader. Drive SCSI ID -- Sets the SCSI ID of the drive. Loader Parity -- Enables/Disables the parity checking for the loader SCSI bus. The default Vendor ID is "Tandberg Data". Other predefined Vendor ID's can be selected by scrolling through a list of choices or enter a unique string by selecting the <Vendor Unique> setting. The default selection for this option is SLR Autoloader. [. . . ] (max. ), including picking from slot Unload Time 10 sec. (max. ), including returning to slot Load to Ready Time 30 sec. (max. ) Sustained native data transfer rate, maximum SLR140 6. 0 MB/sec ­ 21, 6 GB/hr* SLR100 5. 0 MB/sec - 18 GB/hr* SLR75 4. 0 MB/sec ­ 14, 4 GB/hr* SLR60 4. 0 MB/sec ­ 14, 4 GB/hr* *GB/hour rates are nominal and may vary due to site-specific factors Native Data Capacity (Full Magazine) SLR140 SLR100 SLR75 SLR60 560 GB 400 GB 300 GB 240 GB Reliability Specifications MTBF robotics electronics MTBF power supply MTBF tape drive MTTR Warranty Robotics Mean-Exchanges-Between-Failures (MEBF) 250, 000 hours 100, 000 hours 300, 000 hours 30 min 3 years factory 250, 000 cycles Power Specifications Voltage Amperage Line Frequency 110-240 VAC 0. 5-0. 3 A 50-60 Hertz Tandberg SLR Autoloader Servive and Repair Manual 81 Tandberg Data Appendix A - Specifications Notice This product complies with the requirements for an IT Power System. Mechanical Specifications Height Width Depth Weight Shipping Weight Shipping Size Height Width Depth 6. 84 in (17. 4 cm) 8. 80 in (22. 4 cm) 22. 75 in (57. 8 cm) 30 lbs (13. 6 kg) 32 lbs (14. 6 kg) 12. 4 in (31. 5 cm) 13. 8 in (35. 1 cm) 29. 2 in (74. 2 cm) Environmental Specifications Operating Ambient Temperature Temperature Gradient Wet Bulb Temperature Relative Humidity (non-condensing) Altitude Non-Operating (Packed or Unpacked) Ambient Temperature. Relative Humidity (non-condensing) Altitude +41°F to +104°F (+5°C to +40°C) 2°F/min, 18° hour (1°C/min, 10°C/hour) 79°F (26°C) 20% to 80% -1000 to +10, 000 ft (-304. 8 m to +3048 m) -4°F to +140°F (-20°C to +60°C) 2°F/min, 36° hour (1°C/min, 20°C/hour) 84°F (29°C) 10% to 90% -1000 to +40, 000 ft. [. . . ]