User manual TANDBERG STORAGELOADER INSTALLATION AND USER MANUAL

[. . . ] StorageLoaderTM INSTALLATION AND USER MANUAL TANDBERG DATA ASA P. O. Box 134 Kjelsås N-0411 OSLO, NORWAY Phone + 47 22 18 90 90 Telefax + 47 22 18 95 50 www. tandberg. com © Tandberg Data ASA Part No. May 433061-04 2006 Related publications available from Tandberg Data ASA: Part No. 432980 433060 Title Tandberg Data StorageLoader SCSI Interface Functional Specifications. [. . . ] StorageLoader FW id and revision Current Inquiry Vendor Id Current HW/FW Product Id SCSI Id 0 to SCSI Id 15 Disabled, Enabled View status for each loader slot VS160: AT1280- 1R VS160 LTO : AT1280- 1R VS160 AT3200- 1R LTO2 StorageLoader Enabled, Disabled Disabled Enabled if installed, else Disabled --xx. yy "TANDBERG" AT1280- 1R VS160 or AT3200- 1R LTO2 SCSI ID = 4 Enabled Not applicable VS160 : AT1280- 1R VS160 Audible Alarm Disabled * Can only be enabled if a barcode scanner is installed. 4. 5. 2 Drive Info The different drive t ypes used in t he St orageLoader m ay not provide all t he inform at ion list ed below. I f an unavailable ent ry is selected, the string "Data Unavailable is displayed. Item name Drive Product ID Drive Vendor ID Drive FW Revision Drive Serial No. Drive SCSI Id Legal values Drive Inquiry Product Id Drive Inquiry Vendor Id Drive Firmware Revision Drive Serial Number SCSI Id 0 to SCSI Id 15 Default value Drive dependent Drive dependent Drive dependent Drive dependent SCSI ID = 5 38 StorageLoader Installation and User Manual Tandberg Data Operation and Configuration 4. 5. 3 Remote Management Info The Rem ot e Managem ent ( RMM) set up is shown in t he choices list ed below. This m enu t hree is t he place t o find t he current ly allocat ed dynam ic I P address, default gat eway and net work m ask when running in DHCP m ode. The MAC address of t he Loader is also shown here. Item name IP address mode Static IP address Static netmask Static default gateway Dynamic IP address Dynamic netmask Legal values Static mode, DHCP mode 0. 0. 0. 0 to 255. 255. 255. 255 0. 0. 0. 0 to 255. 255. 255. 255 0. 0. 0. 0 to 255. 255. 255. 255 0. 0. 0. 0 to 255. 255. 255. 255 0. 0. 0. 0 to 255. 255. 255. 255 Default value DHCP mode 0. 0. 0. 0 0. 0. 0. 0 0. 0. 0. 0 Not applicable Not applicable Not applicable Value is fixed Dynamic 0. 0. 0. 0 to default gateway 255. 255. 255. 255 MAC- address Value is fixed 4. 5. 4 Statistics Item name Fetch Statistics Stow Statistics Power On Time Time since clean Description When select ed, t he operat or can scroll t hrough t he fet ch count and fet ch ret ries for t he drive and all magazine slots. When select ed, t he operat or can scroll t hrough the stow count and stow retries for the drive and all magazine slots. Displays Power On Hours for the loader I f available from t he drive, t his ent ry displays num ber of hours since t he drive was last cleaned. 4. 6 Utilities Menu Option Maintenance Description Displays a set of maintenance functions StorageLoader Installation and User Manual 39 Tandberg Data Operation and Configuration Diagnostics Access control Displays a list of exercise test programs Set Password 4. 6. 1 The Maintenance Menus Item name Description Prepare to Ship When selected the robotics will be positioned for installation of the locking screw. It will eject the Right magazine to facilitate the installation. It will also eject the left magazine if it contains one or more cartridges. The Loader cannot be safely shipped with cartridges in the magazines This option must be executed before the loader is prepared for transport by inserting the Locking Pin. (See chapters 3. 1, Performing the Installation and 6. 4, Reinstalling the Transport Lock. ) Clean Drive Performs a drive clean provided a slot is reserved for a cleaning tape and a cleaning tape is present Sets the loader settings to their factory default values. This is useful when the password is lost. Performs a hard reset of the loader. Restore default Clear Web Password Reboot 4. 6. 2 The Diagnostics Menu Item name System test Description Starts a test where cartridges are moved randomly between magazine slots and between the drive and the magazines. Starts a test where cartridges are moved randomly between magazine slots. (Only when supported by the installed tape drive. ) Runs a test of the loader hardware, including the Loader internal cabling. Move medium test Drive test Hardware test 40 StorageLoader Installation and User Manual Tandberg Data Operation and Configuration 4. 6. 3 Set Password Item name Set Password Description Allows the operator to set a four- digit password protection for the menu system. The default password is <0000>, meaning the password is disabled. WARNING: If you set a password, make sure you do not forget it. If you do, it ca n on ly be cle a r e d w it h a ssist a n ce fr om Ta n dbe r g D a t a t e ch n ica l support or by a qualified service technician. 4. 7 Cartridge Handling 4. 7. 1 Cartridge Slot Numbers The cart ridge slot s have been given num bers as follow: ( see also Figure 2. 3 Internal components of the StorageLoader) Left m agazine: Slot 1, Slot 2, Slot 3 and Slot 4 ( lowest num ber closest to the front) Right m agazine: Slot 5, Slot 6, Slot 7 and Slot 8 ( lowest num ber closest to the front) 4. 7. 2 Moving Cartridges to and from the Drive The norm al operat ions of t he unit are cont rolled by t he host soft ware applicat ion. When you m ust load or unload a specific cart ridge using t he cont rol but t ons on t he front panel, do t he following: To load a cartridge to the drive: 1. From t he default display press t he m enu but t on and select Load t o Drive from t he m ain m enu. A screen pict ure like figure 4. 11 will be displayed. I f a Barcode reader is im plem ent ed, t he selected cartridge's barcode is displayed in the bottom line. Ok Load to drive From Slot: 135 Figure 4. 11 Load to Drive Cancel 2. Select t he slot num ber of your choice. [. . . ] Reboot the loader and retry the operation. Verify that the cartridge is not damaged. Retry the operation with a new magazine Defect robotics, defect magazine, defect cartridge (This error code is reserved for future use) Cartridge blocked, faulty robotics 01ZZ Diagnostic number ZZ failed. Initialization of the robotics failed. 0200 1001 Failed moving the robotics. [. . . ]