User manual TANNOY FX 5.1

[. . . ] Ensure there are no stray wire strands that could possibly short together and damage both the amplifier and subwoofer. WARNINGS · Double-check all connections before switching on the FX 5. 1 system and your amplifier. POSITIONING As the FX5. 1 subwoofer produces low frequencies only, it is difficult to detect its location by ear. It can therefore be placed anywhere in the room, but optimum performance will be gained by locating the subwoofer between the front pair of speakers. Bass output will increase next to a wall or especially in a corner; so use the VOLUME control to compensate if moving your subwoofer around. · Ensure that the polarity of the speaker cables from your amplifier to the subwoofer is correct - failure to observe this will result in damage to your amplifier. [. . . ] POWER REQUIREMENTS Check that the voltage rating displayed on the rear panel is correct for your area before connecting. If it is incorrect, move the voltage selector on the rear panel to the appropriate voltage. The panel mounted fuse should also be changed to the correct rating (see below, under FUSE PROTECTION). If in any doubt, consult your Dealer or Authorised Service Agent. 5. 1 PERFORMANCE Recommended amplifier power Maximum Sensitivity (2. 83Volts @ 1m) Nominal impedance: Frequency response (-6dB) Drivers: Crossover frequency Magnetic shielding: Weight: Dimensions H x W x D: Finish Supplied accessories Optional accessories IMPORTANT A mains cable is supplied - where the moulded plug is fitted with a mains fuse, always replace with the same type and rating. If the fitted plug is unsuitable for your type of outlet sockets, it should be cut off and disposed of safely. The wires in the mains cable are coloured in accordance with the following code: GREEN AND YELLOW BLUE BROWN EARTH NEUTRAL LIVE As the colours of the wires in the mains cable may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · The wire that is coloured GREEN and YELLOW must be connected to the terminal in the plug that is marked either by the letter E, the earth safety symbol, or coloured GREEN or GREEN and YELLOW. · The wire which is coloured BLUE must be connected to the terminal in the plug which is marked by the letter N or coloured BLACK. · The wire which is coloured BROWN must be connected to the terminal in the plug which is marked by the letter L or coloured RED. · Ensure that the terminals are tightened securely, and no loose strands of wire are present. Ensure cord grip is clamped over outer sheath of cable, rather than over the wires. FUSE PROTECTION An additional mains fuse is provided in the IEC power inlet on the amplifier panel, removable with a screwdriver. A fuse of the same type and rating must always replace this. The correct type is 5mm x 20mm Time Delay (Type T): · T1. 6AL / 125V for AC 220-240V / 50Hz operation, · T800mAL/ 250V for AC100-120V / 60Hz operation. Tannoy Limited, Home Audio Division, Coatbridge, Scotland, ML5 4TF. Tel: +44 (0) 1236 420199 Fax: +44 (0) 1236 428230 e-mail: sales@tannoy. com www. tannoy. com Tannoy adopts a policy of continuous improvement and product specification is subject to change. If you suspect a problem with your loudspeakers, please contact your local Tannoy dealer who will be able to advise on appropriate action. 6481 0381 5. 1 SATELLITES 15 - 100 watts 85dB 6 ohm 140Hz-78kHz HF: 15mm (5/8 inch) titanium dome, Neodymium magnet system. LF: 75mm (3 inch) paper cone 4. 5kHz (mid to high) 140Hz (to subwoofer) Yes 750gms (1. 65lbs) 140 x 97 x 95mm 5 1/2 x 3 4/5 x 4 5/16 inch Silver or black Wall mounting brackets 25 metres (82 ft 6") speaker cable Satellite floor stands available in matching silver & black PERFORMANCE Power output Frequency response (-6dB) Driver Inputs Power requirements SUBWOOFER 100W RMS 45Hz - 140Hz 200mm (8 inch) paper cone Twin line or speaker level 115 or 230V AC / 50 - 60 Hz, switching facility on amplifier panel, 160VA max. AC100-120V / 60Hz - Fuse: T1. 6A L /125V. AC 220-240V / 50Hz - Fuse: T800mA L /250V ON / OFF/ AUTO power function 10kg (22lbs) 400 x 230 x 405mm 15. 75 x 9. 0 x 16. 0 inch Silver or black Fuse ratings Additional features Weight Dimensions H x W x D Finish Due to our policy of continuous improvement, this is a specification update sheet that should be read along with the manual as it provides the latest correct information. All specifications may be subject to further change without notice. FOR YOUR OWN PROTECTION · Store the complete packaging in case it is needed for re-use. · Never expose the unit to moisture, water and extremes of temperature or humidity. Specifically, the unit shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the unit. [. . . ] · When set to the 'standby' and 'off' functions, a small amount of current continues to flow to the apparatus when not in use. If not used for a long period of time, it is recommended that the apparatus is completely disconnected at the AC mains socket. · Terminals marked with the flash symbol are hazardous live and the external wiring connected to these terminals requires installation by an instructed person or the use of a ready-made lead or cord. · This apparatus is designed for use in moderate climates. [. . . ]