User manual TANNOY ST200

[. . . ] Provision for driver magnet system earthing (as in Prestige HE series), to avoid interference and information masking caused by radio interference. High purity (99. 999%) solid silver internal wiring, PTFE coated dielectric. Gold plated terminals, adjustment screws and circuit board for high signal transparency. Radio Frequency quality inductors in crossover for good high frequency characteristics. [. . . ] 1 Initial Positioning With a Tannoy Dual Concentric loudspeaker system, the low and high frequency radiation is generated on the same axis. This is done by mounting the high frequency unit behind the low frequency one, and coupling it to the low frequency radiator via a carefully optimised waveguide through the centre of the drive unit. Low and high frequencies are thus fully integrated at source, to give the most accurate reproduction. The sound will therefore appear to emanate from a point source a little behind the front of the speaker cabinet. The SuperTweeter then needs to be positioned to coincide with this point for best results. For this reason, an alignment gauge, covering our current and past models is included. 2, position the felt mat centrally on the loudspeaker enclosure, then the alignment gauge such that it is flush with the front of the cabinet. Use of the felt mat is optional, but does aid performance by preventing unwanted reflections from the cabinet top. Next, using Table 1, place the Performance Platform in the correct position for your loudspeakers. The distance shown is from the front edge of the cabinet, and refers to the letter coded marking on the alignment gauge. Note that due to the large distance involved, the alignment gauge is unsuitable for the Autograph- please use a tape measure in this case. Finally, withdraw the alignment gauge from under the Performance Platform, ensuring it does not move. The SuperTweeter is then positioned on the Performance Platform, making sure the front two cones engage the two indents in the SuperTweeter housing. PART No. 6481 0325 M M L L PRESTIGE 14kHz CROSSOVER FREQUENCY 16kHz 18kHz MADE IN GRE AT BRITAIN SENSITIVITY 90. 5dB 92dB 93. 5dB B A ST-200 PRESTIGE SUPERTWEETER ALIGNMENT GAUGE B A POSITION ON FRONT EDGE OF CABINET Fig. 2 89dB 95dB MODEL 6 1/2" Dual Concentrics: D100, D300, System 6 8" Dual Concentrics: Esher SL25, NFM 8, DTM 8, System 8, D500, D750 Greenwich 10" Dual Concentrics: LSU/HF/3LZL (Monitor Red)*, LSU/HF/3LZG (Monitor Gold)*, HPD295*, [*General setting, from baffle front], Darking SL35, Windsor, Ascot T125, Chester T165, Dorset T185, Mayfair T225 Buckingham System 10 D700 3LZ, Chevening, Eaton, Caernarvon, SRM10B Stirling/HW Stirling/TW/TWW, Turnberry HE Stirling HE 12" Dual Concentrics: LSU/HF/12L (Monitor Silver)*, LSU/HF/12L (Monitor Red)*, LSU/HF/128G (Monitor Gold)*, *[General setting from baffle front]. HPD315* *[General setting from baffle front]. System 12, D900 Canterbury (corner), Lansdowne, Chatsworth, Lancaster 12, DC4000, Edinburgh/HW, Canterbury 12, SRM12X, LGM (Little Gold Monitor) Mansfield, Devon, Cheviot, Bradley SL65, Chertsey SL45, Balmoral Edinburgh/HW, Canterbury 12, Edinburgh/TW/TWW/HE 15" Dual Concentrics: Monitor Black*, HPD383*, Albury LSU/HF/15L (Monitor Silver)*, LSU/HF/15L (Monitor Red)*, LSU/HF/158G (Monitor Gold)* *[General setting from baffle front]. System 15, System 215 Amesbury, Berkeley, Arden, Arundel, Balmoral, M3000 York, Lancaster 15, SRM15X, FSM, M1000, SGM1000, SGM3000 Dreadnought GRF (horn), Canterbury 15 (incl. HE) GRFM/HW GRFM/TW/TWW/HE, Westminster TW RHR Westminster Royal/HE Autograph DISTANCE POSITION SENSITIVITY XOVER FREQ 45mm A 89dB 18kHz 57mm 87mm B D 90. 5dB 90. 5dB 18kHz 18kHz 78mm C 90. 5dB 14kHz 78mm 78mm 78mm 105mm 105mm 105mm 105mm C C C F F F F 92. 0dB 92. 0dB 92. 0dB 90. 5dB 92. 0dB 92. 0dB 90. 5dB 14kHz 16kHz 18kHz 14kHz 14kHz 16kHz 18kHz 87mm D 92. 0dB 14kHz 87mm 87mm 120mm D D G 90. 5dB 93. 5dB 92. 0dB 14kHz 16kHz 14kHz 120mm G 90. 5dB 14kHz 120mm G 93. 5dB 16kHz 100mm 100mm E E 92. 0dB 93. 5dB 14kHz 14kHz 100mm 130mm 130mm 130mm 155mm 195mm 195mm 247mm 317mm 405mm E H H H J K K L M - 95. 0dB 92. 0dB 93. 5dB 95. 0dB 95. 0dB 95. 0dB 95. 0dB 95. 0dB 95. 0dB 95dB 16kHz 14kHz 14kHz 14kHz 14kHz 14kHz 14kHz 14kHz 14kHz 14kHz TABLE 1 Adjustments Referring to Table 1 again, select the sensitivity and crossover frequency settings to suit your loudspeakers, and install the adjustment screws into the correct position on the SuperTweeter adjustment panel (Fig. The rear support cone on the Performance Platform may be adjusted for height, then secured using the locking thumb screw. If possible, adjust so that the SuperTweeter is pointing at ear height when seated. After double checking the wiring, you are now ready to switch your amplifier on. [. . . ] The walnut enclosure has been hand waxed before dispatch from our finishing workshop. To maintain the natural wood appearance, it is important that only a wax of similar formulation is used. A jar of specially formulated wax is available from your authorised Tannoy dealer. This should be applied carefully (to avoid brass adjustment panel and terminals) and sparingly, with a soft lint-free cloth, such as muslin. [. . . ]