User manual TASCAM CC-222SLMKII

[. . . ] » CD Recorder/Cassette Deck D01022120A CC-222SL@# Professional OWNER'S MANUAL IMPORTANT SAFETY PRECAUTIONS 1 ­ Introduction CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. [. . . ] 7 Tape STOP key Stops the current tape transport operation. 8 Tape PAUSE key Stands by for tape playback or recording. Pressing this key again resumes the operation. 9 Tape PLAY key Starts tape playback or recording, from right to left. 0 Tape PLAY¥ key Starts tape playback or recording, from left to right. q CONT PLAY key Use this key to turn continuous playback (alternating between disc and cassette) on and off. w AUTO SPACE key Automatically adds a space of about four seconds between disc tracks on playback. 14 TASCAM CC-222SLMKII 3 ­ Menu operation Menu operation The following are the menu items that can be set using the MENU key. The majority of them affect disc recording. Pressing the MENU key repeatedly cycles through the menu items. Not every menu item is available in every situation (for instance, if a digital input is not selected, the digital direct option is not shown). 1 PresstheMENUkeyuntilthedesiredmenuis shownonthedisplay. 2 TurntheMULTI DIALtochangeavalueorsetting. 3 PushtheMULTI DIALtoconfirmthechangeandexit themenuitem. Alternatively, keeppressingtheMENUkeyuntilthe normaltimecounterisdisplayed. Menu configuration Menu displayed CD PITCH PITCH CD KEY KEY LEVEL SRC VOLUME A_TRK A_TIME S_LVL COPY ID FADE IN FADE OUT DUB>VOL PHONO MP3 DIR OUT2 Meaning Default (factory) value OFF 0. 0% OFF 0 ON 0dB LEVEL 1 min ­24 dB (analog) ­54 dB (digital) 1 GEN 3s 3s THRU DISC OFF TAPE Described in: "Pitch control playback" on page 19 "Pitch control playback" on page 19 "Key control playback" on page 19 "Key control playback" on page 19 "Sampling Frequency conversion" on page 21 "Signal volume" on page 21 "Automatic track division" on page 26 "Automatic track division" on page 26 "Setting the trigger level" on page 25 and "Using the trigger level" on page 25 "Copy-protection" on page 27 "Fade-in and fade-out" on page 27 "Fade-in and fade-out" on page 27 "Dubbing tapes from the CD deck" on page 31 and "Dubbing from tape to disc" on page 24 "Recording tapes from the PHONO deck" on page 32 and "Recording to disc from the RIAA PHONO inputs" on page 23 "Playing back MP3 files" on page 20 "OUT2 setting" on page 33 Pitch control setting ON/OFF CD pitch control setting Key control setting ON/OFF CD key control setting Sampling rate converter Digital volume control Automatic track increment Automatic track increment Sound (trigger) level for track increment Copy-protection on recorded discs Allows fade in of recorded discs Allows fade out of recorded discs Bypasses (THRU) or enables (ON) internal volume when dubbing from tape to disc or disc to tape Sends the PHONO inputs to DISC or TAPE MP3 directory Assign the OUTPUTS2 jacks to TAPE or DISC TASCAM CC-222SLMKII 15 4 ­ Disc operations 1 ­ Introduction Simple playback operations WARNING If you are monitoring using headphones, first adjust the level control to low on the unit, then connect to the PHONES jack before playing back. This will prevent any possible damage to your hearing. 2 PressthePLAYkeytostartplayback The track number indicators at the bottom of the display light, to show the available tracks playing back. If there are thirteen tracks on the disc, for example, indicators 1 through 13 will light. If there are more than 20 tracks on the disc, "OVeR" will light at the end of the track number indicators. Pressing the PAUSE key pauses playback temporarily. To resume playback, press the PAUSE key again or the PLAY key. 1 Insert a disc with the label side uppermost until the unit pull the disc in. When a disc is loaded into the unit, the display briefly shows TOC Reading. with a flashing period as the unit , determines the contents of the disc. When the TOC has been read, the display shows (at the left of the display) one of the following: CD CD-R/CD-RW CD-R, NO TOC CD-RW, NO TOC Commercial pre-recorded CD Finalized CD-R or CD-RW CD-R which has yet to be finalized CD-RW which has yet to be finalized Time display modes When playing back a CD, or when in standby mode, there are four different time display modes. In each mode, the current track number is given, fol-lowed by the time, as given below, e. g. 1 r 0 48 0T : NOTE If the Program playback has been selected (see "Program playback" on page 17), the elapsed time and total remaining time refer to the programmed material, not the whole disc. Press the DISPLAY key to cycle through these time display modes, as described here: Display shows TOTAl TOTAl ReMAiN [blank] ReMAiN Meaning Total elapsed time of the disc Time remaining of the current disc Elapsed time of the current track Time remaining of the current track Track search Use the MULTI DIAL (or the SKIP keys on the remote control unit) to jump forward or backward by one track at a time, as shown on the display. [. . . ] If AUTO is selected, the unit outputs either the cassette tape or disc automatically when playing back or monitoring. However, note that if both are playing at same time, the cassette takes priority (the disc will not be heard through these outputs). PresstheMENUkeyuntilthemenuitemOUT2>XXX showsuponthedisplay. PushtheMULTI DIALtoconfirmandexitthemenu operation. TASCAM CC-222SLMKII 33 8 Reference Reference and specifications 1 ­ Introduction specifications 8 ­ and Error messages Message Cannot Rec! [. . . ]