User manual TASCAM CD-302

[. . . ] » CD-302 Dual CD Player 9101429501 BRAKE BRAKE OWNER'S MANUAL Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. . [. . . ] (see 4. 10, "Memories") The cue point cannot be updated during A-B LOOP play. 3. 3. 2 Auto Cue The auto cue function allows searching the track and auto-locating to the point where the audio level first goes above a set threshold level. When this point is reached, the unit enters pause mode. Select the threshold level can be selected from: OFF, ­72, ­66, ­60, ­54, and ­35 dB. When the auto cue function is on, the AUTO CUE indicator in the display lights. 2 Select 15 A/CUE (A_CUE) using the dial or numeric keys. 4 Select the threshold value to be used for the auto cue function. 5 Press the ENTER key. 3. 4 Loop play 3. 3. 3 Cueing using the JOG dial You can directly cue to any point using the JOG dial by frame accuracy, while the unit is in pause mode. You can select the resolution of the dial so that one rotation of the dial is equivalent to either 9, 18, or 36 frames. 1 Press the PRESET key. 3. 4. 1 Selecting the loop mode 3 loop modes are available, as shown on the display: ALL--the whole SINGLE--a single track is repeated A-B--between two points TASCAM CD-302 17 3 · Basic operations--Loop play 3. 4. 2 A-B loop play mode The A-B loop mode allows seamless loop play between two points (A and B). The A and B points should be in the same track. 2 Select 01 LOOP (LOOP) using the dial or numeric keys. The A-B indicator on the display lights. If the A and B keys are not lit, pressing the LOOP key will have no effect. If the LOOP key is lit, and you press it again while playing back between the loop points, looped playback stops, but the unit continues to play past the end loop point. If you press the B key while the unit is playing back inside the A-B loop, the point where you press the B key becomes the new loop end point (shortening the loop). If you press the PLAY/PAUSE key while the A-B loop is being played back, playback stops. 3. 4. 3 Setting A-B loop points When you press the A or B key S, you will capture the appropriate loop point. 1 Make sure the A and B keys are turned off (unlit). Locate to the location to be used as the start point of the loop (this can be done "on the fly" during playback). 2 When you press the A key, the current location is captured as the loop start point. 3 Locate to the location to be used as the loop end point (or continue playback until the end point is reached). 4 When you press the B key, the current position is captured as the loop end point. If the A and B locations are different, both the A and B keys light. If you set the loop points during playback, looped playback mode will start when both points have been set. [. . . ] In single play mode (3. 2, "Play modes") this setting has no effect. 28 TASCAM CD-302 4 · Advanced Operations--Relay Play 4. 19 Relay Play Relay play is enabled on this deck. 1 Press the PRESET key. 2 Select 20 DIRECT (DIRECT) using the dial or numeric keys. 4 Select On or Off to turn the function on or off. 5 Press the ENTER key. Playback stops The other deck automatically starts playing 4. 21 Disc Tray Auto Close When you enable this function, any disc tray that is open will close automatically after one minute. [. . . ]