User manual TASCAM CD-A500

[. . . ] » CD-A500 D 3D0017100A Compact Disc Player/Reverse Cassette Deck Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NEDERLANDS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The player automatically returns to point A and restarts playback. When play reaches point B, the player returns to point A and starts playback again, repeatedly. O After designating point A, when quick searching point B, use the Ò or Æ button instead of playing back normally. O When the A-B button is pressed again during block repeat play, block repeat playback will be released. 2. Select the required tune by pressing the ÚÆ button. The selected tune is played, then when the end of the tune is reached, the player will return to the beginning of the tune and playback starts again. In this way, the selected tune will be played back repeatedly. To repeat an entire disc (All Repeat mode) 1. Playback starts and, when the end of the disc is reached, the player will return to the beginning of the first tune, and then playback continues repeatedly. Programmed repeat playback The repeat function can be activated even in the Programmed Playback mode. To repeat all the programmed tunes, press the REPEAT 1/ALL button twice. (At this time, check that the REPEAT and ALL indicators light. ) _9_ Time Counter Display The time counter shows various time readouts, as follows. Auto Spacing When this function is activated, an interval of approx. 4 seconds will be inserted between tunes automatically, so they are played back with a fixed spacing. To activate this, press the AUTO SPACE button so that the A. SPACE indicator lights in the display. When the AUTO SPACE button is pressed again, the indicator goes off and the auto spacing function is released. Single Playback 1. The SINGLE indicator will light in the display. Press the Ú/Æ SKIP buttons corresponding to the required tune. A single tune will be played back, after which the player will enter the stop mode. O To release the Single mode, press the SINGLE button again. 1 Total disc playback time After the disc tray is closed with a disc loaded, the total disc playback time and total number of tunes on the disc are displayed. 2 Elapsed time display When playback begins, the elapsed time of the tune being played is displayed in minutes and seconds. 3 Remaining time display (REMAIN) Displayed when the TIME button is pressed once. This provides an easy check of the remaining time of the tune being played. 4 Total remaining time display (TOTAL REMAIN) Displayed when the TIME button is pressed twice. The time displayed is the total remaining playback time from the position being played, to the end of the disc; the counter counts down to "00:00" during playback. Intro Check Function The intro check function allows only the beginning of each track to be played for 10 seconds. [. . . ] When replacing the fuse only a correctly rated approved type should be used and be sure to re-fit the fuse cover. IF IN DOUBT -- CONSULT A COMPETENT ELECTRICIAN. Specifications CD player section (Audio) Number of channels: 2 Frequency response: 10 - 20, 000 Hz ± 0. 5 dB Signal-to-noise ratio: 90 dB Dynamic range: 90 dB Total harmonic distortion: 0. 02% (1 kHz) Wow and flutter: Unmeasurable (quartz accuracy) Channel separation: 75 dB Output: 2 Vrms Digital filter: 4-times oversampling Analog filter: 3rd order (Signal format) Sampling frequency: 44. 1 kHz D/A converter: 16-bit linear/channel Channel bit rate: 4. 3218 Mb/sec. Channel modulation code: EFM Error correction: CIRC (Pickup) Type: Objective lens drive, optical 3-beam laser pickup. Objective Lens: 2-dimensional parallel drive Laser Type: GaAIAs type semiconductor laser Wave length: 780 nm Signal-to-noise ratio (overall): 59dB(DOLBY off, 3%THD level, weighted), NR 69 dB (DOLBY NR on, over 5 kHz) Fast winding time: Approx. [. . . ]