User manual TASCAM CD-D4000MKII

[. . . ] » CD-D4000@# CD Duplicator 9101431701 Professional OWNER'S MANUAL Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. . [. . . ] 6 SLAVE drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Care of CD-R media 4 5 5 5 5 5 5 3. 1 Discs recommended for use with the CD-D4000 MKII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. 2 Cleaning of lenses . . . . . . . . . . . . . . . . . . . . . . . . . . There are a few factors affecting the production of CD-R discs using the CD-D4000 MKII which may not be immediately obvious. There are no connections to be made to and from the CD-D4000 MKII other than the power connection on the rear panel, as the unit is completely selfcontained. 4 TASCAM CD-D4000 MKII 2 - Parts of the CD-D4000 MKII The following refer to front panel items only. The only rear panel feature is the power cord, which should be plugged into a power supply that matches the voltage shown on the rear panel label. The indicator on this drive shows when the disc is being accessed. In the "Play audio" mode (see 7. 1, "Play audio track"), a pre-recorded CD may be inserted into this drive, and played back, track by track. The headphone jack and volume controls of this drive are operational in this mode only. 1 Power switch Press this switch once to power on the unit, and again to turn it off. 2 Display The 2 x 16 LCD display displays the menus and submenus available, and also provides information on the status of the current operation, as well as displaying error messages, etc. 6 SLAVE drive The SLAVE drive holds the destination CD. The CD-D4000 MKII cannot record on CD-RW discs (but can use them in the MASTER drive as source discs). The eject button is used to eject the slave disc when no operation is in progress. The indicator on this drive shows when the disc is being accessed for reading or writing. In the "Play audio" mode (see 7. 1, "Play audio track"), an audio CD may be inserted into this drive, and played back. The headphone jack and volume controls of this drive are operational in this mode only. 3 MODE key The MODE key is used to cycle through the different menus and options available to put the unit into the different modes, as explained below. 4 ENTER key The ENTER key is used to confirm the selection of menu items and options. It also acts as a "start" key to start operations. 5 MASTER drive The MASTER drive is used to hold the source CD. This may be a pre-recorded audio CD or CD-ROM which you have permission to copy, a CD-R or a CDRW disc. The eject button is used to eject the master disc when NOTE If a disc is in a drive and cannot be removed by using the eject button, you can insert a thin stiff wire (such as the end of a paperclip) into the hole on the front panel of the drive (under the tray). This will open the tray. Spare parts for the repair of this product will be available for five years following the discontinuation of production. TASCAM CD-D4000 MKII 5 3 - Care of CD-R media The Compact Disc medium is a robust medium, and the discs can survive a good deal of physical abuse. However, there are precautions that you should take when handling CD-R discs which are different to those you should take when handling ordinary CDs. Avoid touching the recording (non-label) side of a disc on which you will be recording. Recording on a disc requires a cleaner surface than playing back, and fingerprints, grease, etc. can cause errors in the recording process. CD-R discs are more sensitive to the effects of heat and ultraviolet rays than ordinary CDs. [. . . ] An error message will be displayed and you should use the MODE key to return to the mode selection. If there has been an error in the comparison (i. e. the two CDs do not match) or if they do not match in any other way (the wrong pair of discs has been loaded), the compare operation will stop at the point at which the mismatch was detected, and the display will show: Compare finished 4 If the MODE key is pressed from the screen above, the display changes: Track 2 01 Play track Previous Pressing the ENTER key will start playing the track before the current track. If the first track is currently being played, and the ENTER key is pressed, the last track will start playing. 5 Fail Pressing the MODE key from the display shown above will change the display again: Track 3 Exit 01 Play 10 TASCAM CD-D4000 MKII 7 - Compare CD-ROM 6 Press the ENTER key from this screen to exit the audio play mode and return to the main mode selection screen. NOTE If the copied CD contains audio errors, you will be able to hear them, but no message will appear on the display. [. . . ]