User manual TASCAM CD-RW2000

[. . . ] » CD Rewritable Recorder Professional 3D0038800A CD-RW2000 OWNER'S MANUAL Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The selected mode is shown in large characters and disappears from the display a few seconds after selecting the mode, when the display returns to its previous mode. 3. 2 Programmed order playback The steps to set up to 25 program steps (tracks) to be played back in a specified order are as follows: 1 Press the PLAY MODE key A until the display shows Program. 2 The display changes to show 0Tr 0:00 00, 3. 3 Repeat play The unit can repeat the whole of the disc (or program) or the current track only. NOTE meaning that no program steps have yet had tracks assigned to them. 3 Use the number keys to enter a track number (including the +10 key to enter values greater than 9, as described in 3. 1. 2, "Track search"). The track entered is assigned to the program step, and the display changes, showing the track number, the total time of the program so far, and the step number, e. g. 2Tr14:56 03. Selecting the repeat mode is only possible using the remote control unit. It is not possible to select the repeat mode using the main unit alone. 1 The unit should be in playback, pause or stop mode. 2 Continue to press the REPEAT key 4 so that the display shows Repeat 1 (the REPEAT 1 indicator lights) to repeat one track, or Repeat ALL (the REPEAT ALL indicator lights) to repeat the whole disc or program. 3 If playback has not started, restart it. To cancel repeat mode, press the REPEAT key so that the display shows Repeat OFF and the REPEAT indicator goes out. 4 The next program step can then be entered. NOTE Steps 3 and 4 above can be carried out from the main unit by turning and pushing the MULTI DIAL control B. 16 TASCAM CD-RW2000 3 ­ Playback operations--CALL playback 3. 4 CALL playback The CALL keys (L and K) allow the unit's playback position to be returned to the point at which playback last started from pause mode. If there is no "call point" (i. e. playback starting from pause), pressing the CALL key will have no effect. It should also be noted that this call function is available in play and pause modes only. Note that the call mode is not available when shuffle mode has been selected (see 3. 1. 3, "Playback modes") and there is no "call point" set. tion of the track as indicated by the subcode, but at the first position of the track where the audio level exceeds a set trigger level. The trigger level is the same as the recording trigger level, as set in 4. 3. 1, "Synchronized recording". Consult this section on how to set the trigger level. To set the Auto Cue function on: 1 Repeatedly press the MENU key (9 or 6) until the display shows A_CUE > XXX where XXX is either ON or OFF. 2 Use the MULTI DIAL control B or the SKIP keys H to set the function to ON. When the function is on, the A-CUE display indicator is lit. NOTE 3. 5 Auto Ready function This function allows the playing back of a single track, and the automatic cueing of the next track ready for playback. The unit is cued to the start of the track as determined by the subcode, not the start of the audio signal, unless the AUTO CUE function is on (see 3. 6, "Auto Cue function"). The unit will enter pause mode in the continue, shuffle and programmed play modes, after the location has taken place. If repeat is active (see 3. 3, "Repeat play"), the unit will enter play ready mode at the start of the next track (REPEAT ALL), or the start of the track which is being repeated (REPEAT 1). To set the function: 1 Repeatedly press the MENU key (9 or 6) until the display shows A_READY>XXX where XXX is either ON or OFF. [. . . ] Seen when a CD-RW disc OPC area is full, and the CD-RW2000 automatically cleans up the OPC area for further recording. Refresh the CD-RW disc using the procedure described in 5. 2. 3, "Refreshing a disc". Error in the drive mechanism. Possible cause and remedy The connections from the CD-RW2000 to the amplifier system have not been made properly, or the input source selector is not at the correct position. Analog and/or digital volume (4. 1. 1, "Signal volume") is set too low. [. . . ]