User manual TASCAM CD-RW4U annexe 1

[. . . ] D00597410A CD-RW4U CD Rewritable Recorder Professional OWNER'S MANUAL Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The equipment draws nominal nonoperating power from the AC outlet with its POWER switch in the OFF position. nätströmställaren skiljer ej hela appaaraten fran nätet. the disc should face the base of the unit, and the disc should be hooked under the lip of the disc tray. When a disc is loaded into the unit, the display briefly shows TOC Reading. , with a flashing period following the word "Reading" as the unit determines the contents of the disc. 9 Display The display is used to show the current status of the unit, as well as the current menu settings. A OPEN/CLOSE key Use this key to open and close the disc tray. The display shows OPEN when the tray is opening and CLOSE when the tray is closing. B MULTI DIAL control Use this control to select tracks for playback, to set parameter values, etc. Typically, turning the control clockwise will increase a value, and turning it counterclockwise will decrease the value. There is no "end-stop" to the control--it may be turned continuously in either direction. In addition, when setting menu values, pushing the control acts like an "enter" key, i. e. the currently-displayed value or setting is confirmed and the display returns to the time display. 2 Remote sensor window This accepts the commands from the remote control unit. Do not cover this window when operating the unit with the remote control unit. 3 INPUT SELECT Repeated presses of this key cycle through the different audio inputs and the input combinations. See "Input selection" on page 19 for full details. 4 SYNC REC key Use this key to turn synchronized recording on and off (see "Synchronized recording" on page 24 for details). 5 RECORD key Use this key to enter record ready mode (see "Recording" on page 19 for details) and also to enter manual track divisions (see "Manual track division" on page 23). C INPUT LEVEL control Use this control to adjust the level of the analog audio signals received at the LINE IN jacks I. D FINALIZE key Use this key to finalize recordable discs. See "Finalizing" on page 12 and "Finalizing discs" on page 27 for details. 6 PLAY/PAUSE key Use this key to start or resume playback or recording. 7 STOP key Use this key to stop playback or recording. E MENU key Repeated presses of this key cycle through the different menu items used to set parameters. F PHONES jack and LEVEL control Use a standard pair of stereo headphones, equipped with a 3. 5 mm plug, with this jack. Adjust the volume from the jack with the control (turn clockwise for higher volume). 8 Disc tray The recorded surface of the disc should face the base of the unit. If the unit is being used in a vertical orientation, the recorded surface of Rear panel G DIGITAL IN (COAXIAL) The IN jack accepts digital audio in IEC60958 TYPE I or II format carried on unbalanced cables. H DIGITAL OUT (COAXIAL) The OUT jack outputs digital audio in IEC60958 TYPE II (SPDIF) format. 14 TASCAM CD-RW4U 2 ­ Introduction to the CD-RW4U--Remote control unit I ANALOG IN (UNBALANCED) These RCA jacks accept analog audio signals from suitably-equipped units (­10 dBV, unbalanced). For details, see the CDRW4U USB Operation Guide. L (AC power) Use the connected power cable to connect the CD-RW4U to the AC power supply. Always ensure that the voltage supplied is the same as that indicated on the rear panel of the CD-RW4U. If you are in doubt, consult a qualified electrician. J ANALOG OUT (UNBALANCED) These RCA jacks output analog audio signals (at ­10 dBV levels, unbalanced) to suitably-equipped units. [. . . ] At the end of the countdown period, the word Complete appears briefly on the display, and the display returns to the track/ time display (of course, there are no tracks, and the disc is as the start, with the total time of the disc available for recording). 5 If you do not want to proceed with the refresh operation, press any other key (such as the STOP key). TASCAM CD-RW4U 29 6 ­ Troubleshooting Symptom No sound on playback (the disc is playing and the time display is incrementing) No meter indication when a source is input D-IN UNLOCK! Possible cause and remedy The connections from the CD-RW4U to the amplifier system have not been made properly, or the input source selector is not at the correct position. Analog and/or digital volume ("Level adjustment" on page 20) is set too low. The signal is being input through an unselected input source ("Input selection" on page 19). A digital input source has been selected, but the source is not connected or is not switched on. [. . . ]