User manual TASCAM CD-RW700

[. . . ] » CD-RW700 CD Rewritable Recorder 3D0031900A OWNER'S MANUAL Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. . [. . . ] 1 Make sure the unit is turned on and a disc is inserted. 2 Press the MENU key (9 or 7) until the display shows TIMER ?. 3 Press the MULTI JOG control B or the ENTER key on the remote control unit 8. 4 Turn the MULTI JOG control or use the remote control unit SKIP keys I to set the timer hour. NOTE The unit uses the 24 hour "military" clock, where 1 p. m. is represented by 13, etc. 5 Press the MULTI JOG control or the ENTER key to confirm the hour setting. The "minutes" value starts flashing. 6 Turn the MULTI JOG control or use the remote control unit SKIP keys to set the timer minutes. 7 Press the MULTI JOG control or the ENTER key to confirm the minutes setting. If the unit has recognized the current disc as nonrecordable, Timer Error!appears when the timer switch is set to REC. If the timer is set with the switch at OFF or PLAY and a non-recordable disc loaded, the unit is then placed in standby, and the switch then set to the REC position, this error message will not appear (of course, recording will not take place under these conditions). 14 TASCAM CD-RW700 3 - Playback operations The CD-RW700 can be used to play back CDs (including CD-R and CD-RW discs that have been recorded and finalized on other types of recorder), as well as CD-R discs and CD-RW discs that have been recorded on the unit. Press the DISPLAY key (A or 6) to cycle through these time display modes, as described below: Display shows Meaning TOTAL [blank] TOTAL REMAIN REMAIN NOTE 3. 1 Simple playback operations 1 Press the OPEN/CLOSE key (3 or 2) to open the disc tray. 2 Discs should be inserted in the tray with the label uppermost. 3 Press the OPEN/CLOSE key (3 or 2) to close the tray again. When a disc is loaded into the unit, the display briefly shows TOC Reading. , with a flashing period following the word "Reading" as the unit determines the contents of the disc. When the TOC has been read, the display shows (at the top left of the display) one of the following: CD CD-R, NO TOC CD-RW, NO TOC CD-RW [blank] Total elapsed time of the disc Elapsed time of the current track Time remaining of the current disc Time remaining of the current track If programmed playback has been selected (3. 2, "Programmed order playback"), the elapsed time and total remaining time refer to the programmed material, not the whole disc. 3. 1. 2 Track search Use the MULTI JOG control B or the SKIP keys on the remote control unit I to jump forward or backward by one track at a time, as shown on the display. Note that going forward from the last track of the disc will "wrap round" to track 1, and going backward from the first track of the disc will "wrap round" to the last track of the disc. The track number indicators at the bottom of the display shows the selected track (the lit indicator at the left of the row of indicators). It is also possible to use the number keys on the remote control unit 3 to jump directly to a particular track: 1 To play tracks 1 through 9, simply press the appropriate key (1 through 9). 2 To play a track whose number is higher than 9, press the +10 key an appropriate number of times to set the "tens" digit of the track number, followed by a single key to set the "units" digit. For example: Track 13 = +10, 3 Track 30 = +10, +10, +10, 0 On the remote control unit only, the SEARCH keys Hcan be used to "fast-forward" and "fast-rewind" through the disc. A commercial pre-recorded CD or a finalized CD-R A CD-R which has yet to be finalized A CD-RW which has yet to be finalized A finalized CD-RW (this differs from a CD, as it may be unfinalized and erased) Unusable or unreadable disc or no disc 1 Press the PLAY key (I or L) to start playback 2 Press the STOP key (H or J) to stop playback 3 Press the PAUSE key (J or K) to pause playback temporarily. The track number indicators at the bottom of the display light, to show the available unplayed tracks. If there are thirteen tracks on the disc, for example, indicators 1 through 13 will light. [. . . ] 7 At the end of the countdown period, the word Complete appears briefly on the display, and the display returns to the track/time display. 3 If you do not want to proceed with the refresh operation, press any other key (such as the STOP key). 4 To refresh the disc, press the MULTI JOG control or press the ENTER key 8. NOTE 5. 2. 2 Erasing a whole disc When you want to erase a whole disc (all the tracks on a disc), follow the procedure below: 1 With the disc loaded, and the unit in stop mode, press the ERASE key (G or D). 2 Turn the MULTI JOG control B or use the SKIP keys I until the display shows ERASE DISC?. This operation cannot be undone. If you are going to refresh a disc, make sure that it contains only recordings that you really want to erase! 5 If the erase operation has been selected, the word ERASE flashes on the display, and the timer starts counting down. [. . . ]