User manual TASCAM CD-RW900

[. . . ] » CD-RW900 CD Rewritable Recorder D00892620A Professional OWNER'S MANUAL Important Safety 1-Introduction Precautions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. [. . . ] Track 103: press `1' and `0' and `3' and 103 will be displayed. After input, press the PLAY key to start playback. Or, the READY key to cue the track at its head position and enter playback standby mode. You can also enter the track number and start playback by pushing the MULTI JOG dial or using the ENTER key. NOTE This function cannot be used in Program or Random mode. Track search Normal search 1 Press the / ° search key continuously on the front panel, or the SEARCH / ° key on the remote control. 2 To stop the search function, simply release the / ° or the SEARCH key. NOTE The search function does not operate with MP3 discs. Direct search By specifying time from the start of a certain track, you can start playback from a specified point of a specified track. The direct search function cannot be used in program or random mode. For MP3 discs, time cannot be specified within a track. However, if you input the three-digit track number, playback will begin from the start of that track. Basic operation 1 During stop, play or playback standby modes, use the number keys on the remote control to input the three-digit track number (such as 002 for track 2), then the desired elapsed time (***min **sec) from the start of that track. Example: To specify 1 min 30 sec from the start of track 2, input "002 001 30". Operation variations Even if the final second is not input, playback will begin from the selected point after pressing the ENTER or PLAY key. Or, if you press the READY key, the unit will enter the playback standby mode at the selected point. Specifying a track number only After inputting the track number, press the ENTER or PLAY key to begin playback of that track, or the READY key to cue the track and enter playback standby mode. NOTE During input, the counter in the display will flash. Pressing the CLEAR key cancels the input at any stage during input. NOTE Instead of inputting the three-digit track number, you can input only the desired track number. Example: To specify track 3, input only "3". Regardless of the time display mode (refer to "Time display switching on page 18), the time from the start of the specified track is displayed. During stop or playback modes, when the final digit is entered, the desired position is automatically located and playback will begin from the desired point. During playback standby mode, at the desired point the unit will enter playback standby mode. NOTE Specifying to the minute After inputting the three-digit track number and the number of minutes after the start of the track, press the ENTER or PLAY key to begin playback of that track, or the READY key to cue the track and enter playback standby mode. Example: To specify 1 min 00 sec from the start of track 2, input "002 001" NOTE If a point which does not exist is entered, setting operation will be cancelled. Following the above example, if "0021" is input, the same position will be located. 16 TASCAM CD-RW900 4-Playback operations 1-Introduction Playback modes There are four different playback modes. The selected mode will be indicated on the left of the display. Continuous playback mode (default setting): no indication lamp Single playback mode: SINGLE lamp is lit Program playback mode: PROGRAM red lamp is lit Random playback mode: RANDOM red lamp is lit The playback mode can be selected using the PLAY MODE key on the remote control unit. Pressing the key changes the playback mode on the display in the following order: Continue®Single®Program®Random You can also select the playback mode using the PLAY MODE option in the PLAY sub-menu (refer to "Operation basics" on page 14). Turning the MULTI JOG dial clockwise changes the playback mode shown on the display in the following order: Mode>Cont®Mode>Single®Mode>Program® Mode>Random Pressing the MENU key or pushing the MULTI JOG dial returns to normal mode from the menu mode. While the mode can be changed from any playback mode, the explanation in this manual will assume the user is starting from the Continuous mode. NOTE The selected playback mode remains after power is turned off. However, the setting of program playback mode will be deleted when power is turned off. Continuous playback Programing is cancelled, and playback continuous in the normal order. 1 During stop, set the Continue or the Mode>Cont mode. [. . . ] There is no audio signal from DIGITAL IN. The sampling frequency of the digital input is not 44. 1 kHz. Editing cannot be performed due to operational restrictions. Menu selection cannot be performed due to selection prohibitions. [. . . ]