User manual TASCAM CD-RW901SL

[. . . ] » CD Rewritable Recorder Professional OWNER'S MANUAL D00964520A CD-RW901SL IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a se rial numbe r located on the rear panel. [. . . ] Whenstopped, setthemodetodisplayContinueor Mode>Cont. TASCAM CD-RW901SL 2. PressthePLAYkeytobeginplaybackinorderof thetracknumber. 1 4 - PlaybackSAFETY PRECAUTIONS IMPORTANT operations Single-track playback This function enables playback of just a single track. Whenstopped, setthemodetodisplaySingleor Mode>Single. 3. Aftertheselectedtrackfinishes, playbackstops. 2. UsetheSKIPkeysorthenumberkeys(0~9)on theremotecontroltoselectthedesiredtrack. The MULTI JOGdialcanbeusedtoselectthetrackalso. Random playback In this mode, the unit will play back all the tracks on the disc in completely random order, regardless of track number. When stopped, set the mode to display Random or Mode>Random. Press the PLAY key and random playback will begin. NOTE Even when the power is turned off, the unit will remain in Random mode. Program playback This function enables playback of selected tracks in any desired order. Up to 99 tracks can be selected for program playback. Whenstopped, setthemodetodisplayProgramor Mode>Program. 3. Whenprogramsettingiscompleted, pressthe PLAYkeytobeginplaybackofthetracksinthe programmedorder. NOTE 2. Usethenumberkeys(0~9)ontheremotecontrol unittoselecteachdesiredtrackforprogramplayback, thenpresstheENTERkey. YoucanalsorotatetheMULTI JOGdialtoselectthe tracknumberandpushtoenter. Thetracknumberwillbeenteredintotheprogram. If the STOP key is pressed without first pressing the PLAY key, all the program data will be erased. When stopped, if the playback mode is switched to another, all the program data will be erased. The programmed play order is not memorized when power is turned off. In this mode, if there are no tracks programed, the CD-RW901SL will not start playback. If an attempt is made to enter more than 100 program steps, the message PGM Full!If the total program playing time exceeds 999 min 59 sec, --- : -- appears on the display. Repeat the above step 2 until the desired program is completed. As the program is being created, the program number and total program playing time is revised on the display. NOTE If the CLEAR key is pressed, the programmed track will be deleted from the last. Time display switching When the TIME key on the front panel or the remote control is pressed, the time display will switch through several modes on the display. When playing an MP3 disc, elapsed track time is always displayed, and the TIME key cannot be used. For details on time display during recording, please refer to "Time display while recording" on page 27. Even when power is turned off, the time display mode setting is retained. · Elapsed track time (no display light indication) · Remaining track time (REMAIN is lit in the display) · Elapsed disc time (TOTAL is lit in the display) · Remaining disc time (TOTAL and REMAIN are lit in the display) When stopped, the total recording time is shown, regardless of the status of the TOTAL and REMAIN indicators. NOTE In program mode, pressing the TIME key displays the elapsed and the remaining time of the whole program. 0 TASCAM CD-RW901SL 4 - Playback operations IMPORTANT SAFETY INSTRUCTIONS EXT SYNC playback In this mode, the unit will play back in synchronization with the clock selected as digital input source (OPTICAL, COAXIAL, AES/EBU). When stopped, use the EXT SYNC option in the PLAY sub-menu (see "Operation basics" on page 16) to set the external synch playback mode on. [. . . ] ThediscisinaformatthattheCD-RW901SLcannotread. Cannotsynchronizewiththedigitalinputclockfromtheselected source. Checktheconnectionwiththesourceunit. Thereisnocallpoint. Pleasesetacallpoint. Messages during operations Message BlankDisc Complete NowOPC* DiscRepair PMAWriting* TOCReading Incomplete!48kFsAdj ContRec Statement Ablankrecordabledischasbeeninserted. [. . . ]