User manual TASCAM CD-VT2

[. . . ] » CD-VT2 Portable CD Music & Voice Trainer D00997320A This device has a serial number on the rear panel. Please record it and retain it for your records. Serial number: __________________ OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS FOR U. S. A. TO THE USER This equipment has Using mics with the trainer tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] When the unit is operating, if you disconnect the power adapter or remove the batteries to turn the power OFF, your settings may not be saved. All the settings might even be initialized, reverting them to their default values. When using this player with batteries, the power turns OFF temporarily if you remove or connect the AC adapter. Turning the power ON and OFF Press and hold the POWER switch on the rear of the unit for about one second to turn its power ON. Release the button when the screen below appears on the display. 1 TASCAM CD-VT2 IMPORTANT and functions of parts Names SAFETY INSTRUCTIONS Control panel 2 TEMPO key Press this key to open the TEMPO CHANGE screen. You can change the playback tempo and turn the VSA function ON and OFF on this screen. (See "Changing the tempo" and "Changing the pitch with the tempo" on page 26. ) 3 KEY key Press this key to open the KEY & PITCH screen. You can change the playback pitch on this screen. (See "Changing only the pitch" on page 26. ) 4 VOCAL CANCEL key Press this key to open the VOCAL CANCEL screen where you can change the VOCAL CANCEL function settings. (See "Reducing the sound of recorded vocals and solo instruments" on page 27. ) 5 EFFECT key Press this key to open the EFFECTOR screen. Make mic effect settings on this screen. (See "Using built-in effects" on page 31. ) 6 TIME DISPLAY key Press this to open the TIME DISPLAY screen, which shows the status of the CD during playback and other information. (See "TIME DISPLAY screen" on page 21. ) 7 LOOP key Turns the loop playback and repeat playback functions ON and OFF. When IN and OUT points are set, this key turns 1 TASCAM CD-VT2 1 Display Shows CD status during playback, device settings and other information. IMPORTANT functions of parts Names and SAFETY PRECAUTIONS loop playback ON and OFF. When they are not set, it turns repeat playback ON and OFF. (See "Loop playback" on page 28 and "Repeat playback" on page 29. ) 8 IN/OUT key Use this key to set the loop playback IN and OUT points. (See "Loop playback" on page 28. ) 9 MISC. key Press this key to open the SETUP & MISC. Set and use the metronome and make various device settings on this screen. 0 TUNER key Press this key to open the TUNER screen. Use this screen for help tuning your instrument. (See "Using the tuner" on page 34. ) q LEVEL key Press this key to open the LEVEL screen. Make independent adjustments to the MIC 1 and MIC 2 input and CD playback volumes on this screen to change the mix balance as you like. [. . . ] NOTE Pressing any of the CD player operation keys will also turn the metronome OFF. Using the tuner & By using a mic to input the sound of an instrument, you can use the built-in tuner to check its pitch. You can also use the tuner to specify a tuning pitch and output it through an attached speaker, allowing you to tune multiple instruments at the same time. 1 PresstheTUNERkeytoopentheTUNERscreen. 2 WiththeMODEvalueselected, usetheVALUE(+, ­) keystoselectoneofthefollowingtunermodes. oscillator mode These modes are explained separately in the following sections. TASCAM CD-VT2 IMPORTANT SAFETY INSTRUCTIONS Other functions AUTO (chromatic tuner) In this ordinary mode, you can tune an instrument while looking at the tuning meter on the screen. [. . . ]