User manual TASCAM DA-20MKII

[. . . ] Please record the model number and serial number and retain them for your records. Model number Serial number WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. For U. S. A TO THE USER Important (for U. K. Customers) DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. [. . . ] ·For high-speed dubbing, signals are not output to the DIGITAL OUT connectors. When high-speed dubbing is performed for a tape recorded in the Long Play mode, no signal is output to the ANALOG OUT connector as well. Making an identical tape including subcodes 5-2-3. Making a tape with the program order changed 1 2 3 4 5 Set the COMMON MODE switch to OFF. Follow the procedure in "6. 6 Program playback" to select the programs to be dubbed. Set the Dubbing mode to DUB MODE PGM with the DUB MODE key. Pressing the DUBBING key rewinds the tape in Deck 2 to the beginning of the tape, then starts dubbing according to the program. 1 2 3 Load the source tape in Deck 1 and the recording tape in Deck 2. Select the Dubbing mode with the DUB MODE key. ·For dubbing at high speed (2 times normal speed), select DUB MODE HIGH and for dubbing at normal speed, select DUB MODE NORM. ·A tape recorded in the Long Play mode can be dubbed at high speed (4 times normal speed). When the DUBBING key is pressed, the tapes in Deck 1 and Deck 2 are rewound, then dubbing starts. . . . When "Cas Out" is set to "Auto" in the menu (úp. 28), playback sound output is switched from Deck 1 to Deck 2 at the time Deck 2 starts playback. In this status, if the PLAY key of Deck 1 is pressed, you can monitor the playback sound of Deck 1 again. 1 2 Set the COMMON MODE switch to OFF. Press the PLAY key to start playback. . . . When the REW key (F FWD key) is pressed during playback, 2 times (3 times) normal speed rewind cueing (fast-forward cueing) is performed. Pressing it once more allows 4 times (6 times) normal speed cueing. Pressing it once more restores 2 times (3 times) cueing. To restore normal playback, press the PLAY key. Holding the REW key (F FWD key) pressed for 1 second or more during playback performs 2 times (3 times) normal speed rewind (fast forward) cueing for as long as the key is pressed. Pressing the REW key during fast-forward cueing switches to 2 times normal speed rewind cueing. Pressing the F FWD key during rewind cueing switches to 3 times normal speed fast-forward cueing . Playback signals are output from the ANALOG OUT and DIGITAL OUT connectors of Deck 1 (Deck 2). 6-3. [. . . ] (LP: Recording/playback) Recording Time : 120 minutes (SP: With a 120-minute tape) 240 minutes (LP: With a 120-minute tape) Fast Winding/Rewinding Time : Approx. 60 seconds (with a 120minute tape) Channels : Stereo 2 channels Quantization : 16-bit linear (SP), 12-bit non-linear (LP) Error Correction Method : Doubled Reed Solomon code Sampling Rates : 48 kHz (recording/playback) 44. 1 kHz (recording/playback) 32 kHz (recording/playback) Emphasis : 50 µsec. /15 µsec (automatically applied in the Play mode) Frequency Response : 20 ­ 20 kHz ± 0. 5 dB (48 kHz/44. 1 kHz) 20 ­ 14. 5 kHz ± 0. 8 dB (32 kHz) S/N : More than 89 dB Dynamic Range : More than 89 dB Total Harmonic Distortion : Less than 0. 007% (SP), less than 0. 07% (LP) (1 kHz for recording and playback, full-scale) Channel Separation : More than 85 dB (1 kHz) Wow and Flutter : Unmeasurable (less than ±0. 001%) Analog Input/Output Connectors IN : RCA pin x 2 Normal Input Level : ­10 dBV (0. 3 V), unbalanced (FS ­ 16 dB) Input Impedance : 20 kohms OUT : RCA pin x 4 Normal Output Level : ­10 dBV (0. 3 V), unbalanced (FS ­ 16 dB) Maximum Output Level : +6 dBV (2. 0 V), unbalanced (10-kohm load) Output impedance : Less than 1 kohm CASCADE OUTPUT : RCA pin x 2 Normal Output Level : ­10 dBV (0. 3 V), unbalanced (FS ­ 16 dB) Maximum Output Level : +6 dBV (2. 0 V), unbalanced (10-kohm load) Output impedance : Less than 1 kohm PHONES: 6. 3 mm dia. phone jack x 1 Maximum Output Level : 50 mW + 50 mW (32-ohm load) Digital Input /Output Connectors INPUTS : RCA pin x 2 Format : IEC958 TYPE I (AES/EBU), IEC958 TYPE II (SPDIF), automatic selection Input Impedance : 75 ohms OUTPUTS: RCA pin x 2 Format : IEC958 TYPE I (AES/EBU), IEC958 TYPE II (SPDIF), selected with menu Output Level : More than 0. 5 Vp-p Output Impedance : 75 ohms CASCADE OUTPUT : RCA pin x 1 Format : Conforming to DIGITAL OUTPUTS Output Level : More than 0. 5 Vp-p Output Impedance : 75 ohms Control Input/Output Connectors INPUT : 3. 5 mm dia. mini-jack Input Level : TTL level OUTPUT : 3. 5 mm dia. [. . . ]