User manual TASCAM DA-302

[. . . ] » DA-302 Dual Digital Audio Tape Deck OWNER'S MANUAL D00313200A Important Safety Precautions Ü ÿ Y CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. [. . . ] When the AUTO ID mode is engaged, a Start ID is automatically recorded at the start of each program to be recorded. 4 . . . To stop dubbing in the middle, press the STOP key on Deck 1 or Deck 2. Dubbing a tape from the middle 1 2 3 Set the COMMON MODE switch to OFF. Select the DUB MODE APPEND with the DUB MODE key. Press the DUBBING key to start dubbing from that point. 16 Section 5 : Recording 5-3. Dual recording Dual recording means recording the same input source on both Deck 1 and Deck 2. 5-4. Continuous recording Continuous recording means recording one input source continuously using tapes in Deck 1 and Deck 2. 1 Connect the input source to the ANALOG IN connectors if it is analog and to the DIGITAL IN "1" connector if it is digital. ·Connecting it to the DIGITAL "2" connector is invalid. Set the COMMON MODE switch to "1&2". For analog input signals, follow procedures 3 to 6 in "5-1-1. For digital input signals, set the INPUT switch to DIGITAL. When Deck 1 is set in the Record mode, recording starts on both Deck 1 and Deck 2 simultaneously. When the Stop key on Deck 1 is pressed, recording on both Deck 1 and Deck 2 stops simultaneously. 1 Connect the input source to the ANALOG IN connectors for analog input signals and to the DIGITAL IN "1" connector for digital signals. ·The DIGITAL IN "2" connector is disabled. 2 3 4 5 2 3 Set the COMMON MODE switch to "1 > 2". For analog input signals, follow procedures 3 to 6 in "5-1-1. For digital input signals, set the INPUT switch to DIGITAL. 4 5 Set "Seqtime" in the menu. When the COMMON MODE switch is set to "1&2", the STOP key, PLAY key, PAUSE key, RECORD key, F FWD key, REW key and REC MUTE key on Deck 1 (Deck 2) are effective for both decks. The input signals during recording are output from the ANALOG OUT connectors and the DIGITAL OUT connector of Deck 1 and Deck 2. Set Deck 1 in the Record mode and start recording. When the ABS time of Deck 1 reaches the time set with "Seqtime", Deck 2 automatically starts recording. 6 Deck 1 rewinds the tape automatically to the beginning either 3 minutes after the time set with ''Seqtime'' or when the tape end is reached. 7 Deck 2 rewinds the tape automatically to the beginning either 3 minutes after the time set with ''Seqtime'' or when the tape end is reached. . . . To stop recording in the middle, press the STOP key on the deck which is recording. The input signals being recorded are output from the ANALOG OUT connectors and DIGITAL OUT connector of Deck 1 (Deck 2). 17 Section 6 : Playback 6-1. The playback sound can also be monitored through the ANALOG CASCADE OUTPUT connectors. When "Cas Out" is set to "Auto" in the menu (úp. 28), playback sound output is switched from Deck 1 to Deck 2 at the time Deck 2 starts playback. [. . . ] mini-jack Output level : TTL level Remote Control Input Connector : 3. 5 mm dia. mini-jack Power Supply : U. S. A. /Canada : 120 V AC, 60 Hz U. K. /AUSTRALIA : 240 V AC, 50 Hz EUROPE : 230 V AC, 50 Hz Power Consumption : 27 watts Dimensions (WxHxD) : 482 x 150. 5 x 353 mm (19" x 6-3/32" x 13-7/8") Weight : 7. 2 kg (15. 9 lbs. ) . . . In these specifications, 0 dBV is referenced to 1. 0 Vrms. However, actual voltage levels are also given in parentheses (0. 316 V for -10 dBV rounded off to 0. 3 V) . . . [. . . ]