User manual TASCAM DR-2D

[. . . ] D01101220B DR-2d Linear PCM Recorder This device has a serial number located on the bottom panel. Please record it and retain it for your records. Serial number: __________________ OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. [. . . ] WAV: 16bit (default), WAV 24bit MP3: 32kbps, 64kbps, 96kbps, 128kbps, 192kbps, 256kbps, 320kbps NOTE · Higher values provide better recording quality. · WAV files are higher quality than MP3 files, but they take up more space, so MP3 formats allow for longer recordings. 4 Press the  key to select the other item. TASCAM DR-2d 33 4­Recording 5 Use the wheel to select SAMPLE, and press the ¯ key or ENTER/MARK key. NOTE · If the maximum set file size is exceeded during recording, the unit will automatically continue recording in a new file. · Depending on the file format, the amount of recording time will differ for the same file size. · Recording automatically stops if recording time exceeds 24 hours. Set the sampling frequency to one of the following options. 44, 1k (default), 48k, 96k 8 Press the Screen. /HOME [ª] key to return to the Home 6 Press the  key to select the other item. 7 Use the wheel to select SIZE, and press the ¯ key or ENTER/MARK key. Available recording time display The amount of time available for recording depends on the capacity of the SD card as well as the recording mode and sampling frequency settings. (See "Recording duration" on page 51. ) You can check the potential recording time determined by the SD card and various settings on the REC SETTING screen. Set the maximum file size to one of the following options. 64M, 128M, 256M, 512M, 1G, 2G (default) Recordable time 34 TASCAM DR-2d 4­Recording Set where to save the file Set the folder where recorded files are saved. If no setting is made, new recording files are placed in the MUSIC folder. (See "Folder operations" on page 54. ) microphone when no microphone cable is connected to the MIC IN jack (stereo mini-jack). When a microphone cable is connected to the MIC IN jack, the input microphone signal becomes the input source. When LINE is selected, sets the source as the line level signal input to the left side panel LINE IN jack (stereo mini-jack). Setting the input functions 1 Press the MENU key to open the Menu Screen. 2 Use the wheel to select INPUT SETTING, and press the ENTER/MARK key. INPUT SETTING screen appears. GAIN: Set the mic input sensitivity as HIGH, MID, or LOW. Change it to HIGH if the input level is too low and to LOW if the input level is too high. TYPE: Select STEREO or MONO according to the type of connected microphone. If you select MONO, the left and right channels are combined into the same signal. POWER: This screen has the following setting items. Use the  and ¯ keys and the wheel to set each item. When connecting a microphone that requires plug-in power set this to ON. The factory default is OFF. INPUT: Set the input source to microphone (MIC) or line (LINE). When MIC is selected, sets the input source as the built-in LOW CUT: The factory default setting of the low cut filter is OFF, but you can also select 40Hz, 80Hz or 120Hz as the cut-off frequency for a low cut filter. TASCAM DR-2d 35 4­Recording LEVEL CTRL: Use this to set the level control function. Set it to AUTO to have the DR-2d automatically adjust the input gain according to the input level. Loud sounds and quiet sounds are both adjusted to the same level. Set it to LMT to have the DR-2d automatically limit the input gain so that input level of loud sounds are reduced to prevent distortion. 3 Press the Screen. CAUTION · Set the POWER item to OFF when using the built-in mic or connecting a dynamic microphone or microphone with a built-in battery. If set to ON, the plug-in power may damage such microphones. [. . . ] If the power cannot be turned OFF, remove the batteries and disconnect the AC adaptor (if connected). If the error message continues to appear, please contact a TEAC Repair Center. Meaning and response 82 TASCAM DR-2d 12­Troubleshooting If you are having trouble with the operation of this unit, please try the following before seeking repair. If these measures do not solve the problem, please contact the store where you bought the unit or a TASCAM Service Center. is supported by this unit. ª No sound is output. · Are headphones connected? [. . . ]