User manual TASCAM FIREONE APPLICATION NOTES 1.00

[. . . ] 4 Metronome mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cakewalk SONAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control Surface Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Change the Display Mode to MIDI Clock Flash or MIDI Clock Rotate. Under the Options menu, select Preferences Choose the "MIDI Sync" tab on the left In the row labeled "Output: FireOne Control" click ON the button in the Sync column. Page 2 of 11 Steinberg Control Surface Configuration · · · · · · · Run the FireOne driver installer and check the box for your desired plug-in (Cubase or Nuendo). Please see the Release Notes for detailed installation instructions. Open the FireOne control panel and ensure the Control Protocol is set to Native Launch Cubase Select Device Setup under the Devices menu Click on the + in the upper right side of the window to add a new device. In the TASCAM FireOne Device window, select FireOne Control for MIDI Input and MIDI Output. Click Apply Control Assignments NOTE: The following default assignments relate to Cubase 4. Not all the commands shown below will be present in other Steinberg apps, such as Cubase 3, Nuendo, or Cubase Studio 4. F1 F2 F3 F4 F5 F6 F7 F8 SHIFT + F1 SHIFT + F2 SHIFT + F3 SHIFT + F4 SHIFT + F5 SHIFT + F6 SHIFT + F7 SHIFT + F8 Show/hide the Time Display Show/hide the Transport Show/hide the Mixer Show/hide VST Connections Show/hide MediaBay Show/hide the Loop Browser Show/hide the SoundFrame Browser Show/hide the DirectShow Video Player New Project Open Project Close Save Save As. . . Add Track > Audio > Mono Add Track > MIDI Display the Project Setup window It is possible to re-assign the above defaults in the Steinberg app: · Select Device Setup under the Devices menu · Click on the TASCAM FireOne device · On the right will be a matrix with two columns of application commands that can be assigned to an F-Key. Click on an item to see other choices or make another selection. · Click Apply Page 3 of 11 Visual Metronome MIDI Clock Rotate and Beat modes · · Open the FireOne Control Panel. Change the Display Mode to MIDI Clock Flash or MIDI Clock Rotate. In the Transport | Synchronization Setup dialog: o Timecode Source = "Internal Timecode" o MIDI Clock Destinations: Check "FireOne Control (Emulated)" Metronome mode · · Open the FireOne Control Panel. In the Transport | Metronome Setup dialog: o Activate MIDI Click o Port = FireOne Control (Emulated) o Channel = 1 o Hi Note = G#4, Middle velocity o Lo Note = A4, Middle velocity NOTE: Turn on the metronome from the transport bar, or select Metronome On from the Transport menu. Page 4 of 11 Cakewalk SONAR FireOne has been tested with SONAR Versions 5 and 6. Control Surface Configuration · · · · · · · · Run the FireOne driver installer and check the box for the SONAR plug-in. Please see the Release Notes for detailed installation instructions. Open the FireOne control panel and ensure the Control Protocol is set to Native Launch SONAR Select Control Surfaces under the Options menu Click on the yellow star to add a control surface From the Controller/Surface pulldown, select TASCAM FireOne Select FireOne Control for both the MIDI Input Port and MIDI Output Port Click OK then close the Controllers/Surfaces window Control Assignments Following are the default F-Key assignments in SONAR. F1 F2 F3 F4 F5 F6 F7 F8 SHIFT + F1 SHIFT + F2 SHIFT + F3 SHIFT + F4 SHIFT + F5 SHIFT + F6 SHIFT + F7 SHIFT + F8 Footswitch All Safe / All Record Clear Solos Clear Mutes Close Window Go | Previous Marker Go | Next Marker Send Enter key Send Space key Set Loop From Set Loop Thru Loop Toggle Set Punch From Set Punch Thru Punch Toggle Edit | Undo Edit | Redo Transport | Record Page 5 of 11 It is possible to re-assign the above defaults in SONAR: · Select TASCAM FireOne under the Tools menu · You will see a pulldown menu for each of the F-Keys (unshifted and shifted) and the footswitch input. · Use the pulldowns to select your desired function for each. · The settings here are remembered globally by SONAR · At the top of this window, there is a standard SONAR interface for saving assignment sets. · At the bottom of this window, you can set the wheel resolution for transport locate. Visual Metronome MIDI Clock Rotate and Beat modes · · · · Open the FireOne Control Panel. Change the Display Mode to MIDI Clock Flash or MIDI Clock Rotate. Under the Options menu, select Project and choose the "Sync" tab Check the box for Transmit MIDI Start/Continue/Stop/Clock Check the box for FireOne Control in the area labeled "MIDI Sync Output Ports:" o It is not necessary to also transmit MTC) Metronome mode: · · · · · · · · · Open the FireOne Control Panel. [. . . ] Under Transmit MIDI Clock, click the Destination 1 checkbox and select FireOne Control Port from the pulldown menu. You should see the FireOne flash in time with the music. Page 8 of 11 Apple Final Cut Pro Control Surface Configuration · · · · · · · Run the FireOne control panel installer Open the FireOne control panel and ensure the Control Protocol is set to Native Launch Final Cut Pro Click the Tools menu and select Control Surfaces. . . · · · Launch DP 5 Load a project that has a MIDI track. Click on the output routing menu for a MIDI track. [. . . ]