User manual TASCAM IF-AE8

[. . . ] The wires in the mains lead on this product are coloured in accordance with the following code: BLUE: BROWN: NEUTRAL LIVE For U. S. A TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residental area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13) Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14) Outdoor Antenna Grounding -- If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and builtup static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 15) Lightning -- For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16) Power Lines -- An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17) Overloading -- Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in risk of fire or electric shock. 18) Object and Liquid Entry -- Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19) Servicing -- Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20) Damage Requiring Service -- Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) when the power-supply cord or plug is damaged. b) if liquid has been spilled, or objects have fallen into the product. c) if the product has been exposed to rain or water. d) if the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e) if the product has been dropped or damaged in any way. f ) when the product exhibits a distinct change in performance ­ this indicates a need for service. [. . . ] Since the resulting data will be at 44. 1 kHz, the DAT playing back the material at 44. 1 kHz (DAT 1) is selected to act as the clock master. Since the TDIF-1 I/O is not used here, the DIGITAL OUT switch 4 is set to DIGITAL IN. The word clock is therefore derived from this, and used to resample the 48 kHz material from DAT 2, and the Fs RATE CONVERT switch 6 is set to CONVERT. Dimensions (w x h x d) Weight Power supply Power consumption Supplied accessories 6 TASCAM IF-AE8 IF-AE8 Digital Audio Converter 4. 1 Dimensional drawing 482mm 466mm 32mm 4. 2 Rack mounting Use the supplied rack mounting kit to install the IF-AE8 in a standard 19" rack, as shown below: 4mm 44mm 194. 8mm 181. 5mm 10. 5mm 4. 3 Block diagram CONVERT DIGITAL I/O INPUTS (AES/EBU) Fs CONVERT THRU Data THRU Fs / Emph D OUT D IN TC9271 DIGITAL I/O OUTPUTS (AES/EBU) 1-2 AD1892 1-2 Digital Interface Receiver FSC CLK TDIF Digital Interface Transmitter AD1892 3-4 Digital Interface Receiver THRU 3-4 FSC AD1892 5-6 Digital Interface Receiver TC9271 THRU 5-6 FSC Digital Interface Transmitter AD1892 7-8 Digital Interface Receiver THRU FSC Fs / Emph 7-8 D IN 7-8 D IN 5-6 D IN 3-4 D IN 1-2 TDIF-1 WORD CLOCK LOCKED Data Out Emph Out LR CLK Out 2 FS Code Out 2 FS Code In LR CLK In Emph In Data In 4 4 DIGITAL I/O (TDIF-1) PLL IN WORD THRU (AUTO TERM) OUT 75 CPU Digital Mixer or DTRS TASCAM IF-AE8 7 » I F-AE8 TEAC CORPORATION Phone: (0422) 52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan 7733 Telegraph Road, Montebello, California 90640 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Privada De Corina, No. 18, Colonia Del Carmen Coyoacon, Mexico DF 04100 5 Marlin House, Marlins Meadow, The Croxley Centre, Watford, Herts. Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany 17 Rue Alexis-de-Tocqueville, CE 005 92182 Antony Cedex, France P. A. [. . . ]