User manual TASCAM MD-02B

[. . . ] D01082620B MD-02 MD-02B MiniDisc Deck OWNER'S MANUAL IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. [. . . ] Use the MULTI JOG dial on the main unit or the number keys on the remote control to select the track number that you want to add to the program, and then press the MULTI JOG dial on the main unit or the ENTER key on the remote control to add it to the program. Repeat step 2 to program additional tracks. As tracks are added to the program, the number of tracks in the program and the program total time shown increase. After finishing setting the program, press the PLAY key to start playing tracks in the program order. Using power on play By using a commercially available timer, for example, to turn this deck's power on, it can be made to begin playback at desired times. TASCAM MD-02/MD-02B 19 5 - Playback NOTE Program data retention · Program data is retained after program playback com· Program playback mode stays active even when the power is turned OFF, but program data is erased. or the remote control discards the program data. pletes and when the STOP key is used to stop playback. · · If you press the STOP key before pressing the PLAY key, the program data is erased. If the total playback time of the programmed tracks exceeds 150 minutes 00 seconds, "---m--s" is shown. Confirming the contents of the program During playback or when playback is paused, turn the MULTI JOG dial on the main unit or use the SKIP keys on the remote control. · When stopped, pressing the STOP key on the main unit · When stopped, pressing the PLAY MODE key on the main unit or the P. MODE key on the remote control exits program mode and discards the program data. discarded. Erasing the entire program When playback is stopped during program playback mode, press the STOP key to erase the entire contents of the program. In addition, pressing the PLAY MODE key on the main unit or the P. MODE key on the remote control to change the playback mode also completely erases the contents of the program. · If group mode is turned on or off, the program data is · If a different group is selected when group mode is on, the program data is discarded. · If an MD is ejected, the program data is discarded. (The playback mode is not changed. ). Random playback In this mode, the unit plays all the tracks on a disc in random order regardless of track number. Removing a track from the program When stopped, press the ESCAPE key on the main unit or the ESC/CLR on the remote control to remove the last track in the program. 1. When stopped, press the PLAY MODE key on the main unit or the P. MODE key on the remote control until "RANDOM" lights on the display. Press the PLAY key on the main unit or the remote control to start random playback. NOTE Random mode stays active even when the power is turned OFF. Adding a track to the program 1. When stopped, use the MULTI JOG dial on the main unit or the number keys on the remote control to show the track that you want to add in the track display area. Press the ENTER key to add this track to the end of the program. Changing the time and character information display ª Changing the time display During playback (or playback standby), press the TIME key on the main unit or the remote control to change the time display option. (The "REMAIN" indicator is lit when the second option is active. ) During playback: track elapsed time, track remaining time ("REMAIN" lit) During recording: record elapsed time, disc remaining time ("REMAIN" lit) NOTE Program restrictions · When group mode is ON, you cannot create a program with tracks from more than one group. · You can repeat the same track in a program. · The maximum number of tracks in a program is 32. If you try to add more tracks, "PGM Full!" appears and they will not be added to the program. is no program data, "PGM Empty!" appears and the deck does not operate. · In program mode, if you press the PLAY key when there · The track remaining time display during playback is the amount of time needed to play until the track end. Note that this differs from the remaining time display during recording. The total playback time is always shown when playback is stopped. · 20 TASCAM MD-02/MD-02B 5 - Playback · For time display when recording and when in recording standby, see "Checking the MD's remaining time" on page 25. The time display setting is retained even when the power is turned OFF. · ª Changing the character display Press the DISPLAY key on the main unit or the remote control when stopped to show the current disc title on the display. Press during playback or in playback standby to show the current track title. [. . . ] No more tracks can be added to the program. An MD that can only be played is loaded. Due to MD system limitations and editing conditions, editing could not be completed. Since group mode is ON, editing is not possible. [. . . ]