User manual TASCAM PT-7

[. . . ] D01088120A PT-7 Chromatic Tuner/ Recorder This device has a serial number located on the bottom panel. Please record it and retain it for your records. Serial number: __________________ OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK , DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] 5 START/STOP key Press this to start and stop the metronome. When tuning, press it to start and stop output of the standard pitch from the built-in speaker. 6 IN/OUT key When playing back a recorded track, press to set and cancel loop playback starting (IN) and ending (OUT) points. 7 LOOP key Press to enable and disable loop playback when playing back a recorded track. 8 MIC Use this built-in monaural microphone for recording and the pitch trainer functions. NOTE When a contact mic or other device is connected to the INPUT jack, the built-in mic is disabled. When you want to use the built-in mic, do not connect anything to the INPUT jack. 9 TAP +/­ keys Use these to set various internal setting parameters. 0 STOP key Press to stop recording or stop the playback of a recorded track. w RECORD key Press this key during playback or when TASCAM PT-7 13 2 ­ Names and functions of parts stopped to start recording. Press this key during recording to start a new track (file) from that point and continue recording. e Â/¯ keys When stopped or when playing back a recorded track, press these keys briefly to skip to the previous/next track. Press and hold these keys to search backward/ forward in a track while playing. r HOME key Press this key to exit the various setting modes. The pameter value display area of the LCD shows the current track (song) number. NOTE If there is no recorded track (file), "- - -" appears in the parameter value display area of the LCD. Rear panel 14 TASCAM PT-7 2 ­ Names and functions of parts t STANDBY switch Use this switch to turn the trainer's power ON and STANDBY. ON: Turns the power on without illuminating the LCD with the backlight. BACK LIGHT: Turns the power on and illuminates the LCD with the backlight. y INPUT GAIN switch Set this to suit the level of the signal input to the INPUT jack. If the input volume is quiet set this to HIGH, and if it is loud set this to LOW. u SPEAKER switch Use this to turn the built-in speaker ON and OFF. Left side panel i PHONES jack Use this to connect headphones. o VOLUME control Use this to adjust the volume of the headphone and the built-in speaker output. p INPUT jack Connect an external contact mic, for example, to the unit here to input sound. NOTE · When a contact mic or the other device is connected to the INPUT jack, the built-in mic is disabled. When you want to use the built-in mic, do not connect anything to this jack. TASCAM PT-7 15 2 ­ Names and functions of parts · This unit does not support the direct input of electric guitars, effect pedals and similar devices. If you connect one of these directly to the unit, recording could be distorted. If this happens, you might be able to record without distortion if you turn down the output of the connected device. Right side panel a DC IN 5V jack Connect a specialized PS-P520 AC adaptor (sold separately). [. . . ] If it is shown, press the IN/OUT key until it disappears. 2 Press the IN/OUT key during playback to set the loop IN point. The left side of the loop indicator lights for the IN point underneath the play position bar on the display. Press the + and ­ keys at the same time to restore the original speed (100%: default value). 36 TASCAM PT-7 3 Press the IN/OUT key again to set the loop OUT point. After the loop OUT point is set, 6 ­ Using the recording and playback functions loop playback starts and the loop indicator appears to turn. [. . . ]