User manual TASCAM TM-D1000 QUICKTIPS

[. . . ] [. . . ] Choose the snapshot and press ENTER (see "Recalling snapshots" on page 26). Monitoring input channels and tape tracks Assign the input channels and tape tracks to the stereo L-R buss (see "Monitoring, etc. " on page 21). Storing a snapshot Press and hold the SHIFT key and press the STORE (ESCAPE/RECALL) key. Choose a memory, and press ENTER (see "Storing a snapshot" on page 26). Panning channels between output busses Use the PAN controls above each channel fader. Making EQ settings Press the PARAM SEL key until the EQ indicator lights green, and then the channel's CH SEL key. Make sure the EQ key by the CH ASSIGN keys is lit, and make the appropriate settings using the data editing knobs (see "Equalization" on page 18). Setting the MMC ID of the TM-D1000 Option « MIDI « MMC Device ID (see "Setting up the device IDs" on page 29). Controlling an external device though MMC Press and hold down the SHIFT key while pressing the MMC control keys (MMC blue labels below the keys)--see "MIDI Machine control" on page 29. Making stereo linked pairs of channels Press and hold down the CH SEL key of an odd-numbered channel, and press the CH SEL key of the next even-numbered channel (you can also press and hold any even-numbered key and press odd-numbered key directly before it)--see "Linking channels for simultaneous parameter adjustment" on page 20. Selecting the MTC type for location operations Option « MIDI « MTC Type (see "Selecting the MTC type" on page 30). Selecting the way in which internal effect units are used Option « Effect « Effect Pattern -- choose an effect pattern which to match your requirements (see "Selecting effect patterns" on page 24). Storing and locating to location memories Use the MEMO key (see "Locations" on page 30). Setting MIDI channels to control the TM-D1000 (Program Change) Option « MIDI « MIDI Ch Select for Selecting and assigning the AUX and EFFECT RETURN controls Option « Setup « Aux Rtn Input/Assign--choose the Mixer, Effects, Dynamics (see "Setting Program Change receive channels" on page 32). the source and the routing of the aux and effect returns. Factory default settings TASCAM TM-D1000 Digital Mixer Connections for your first recording session MODE menu MODE select Buss Function Select MIX ST+4Aux[Mono] ST+4Grp (MIX) / (REC) Setup menu TASCAM TM-D1000 OPERATIONAL QUICK REFERENCE GUIDE All Ch Aux Pre/Post Solo mode Digital Input Digital Out Digital Out Format Direct out mode Effect Rtn Input/ Assign Aux Rtn Input/Assign Ch7-8 Route Target Ch1-8 Input Ch9-16 Input TDIF-1A Direct Out post PFL (In-Place SOLO) In-place SOLO(PFL) A:RCA (REC) / (MIX) (A:B) L-R:1-2 A:SPDIF / B:SPDIF Post Input Fader Input:Effect2 Monitoring system / Assign:L-R / Input:Digital In A Assign:L-R Analog In Analog In TDIF-1A Ch1-8 Multi-effector AES/EBU or SPDIF digital with digital output output Balanced +4 dBu inputs DAT mastering recorder Effect menu Effect Pattern Ch Dynamics (REC) / L-R:Effect1 Aux12:Effect2 (MIX) 1234 DIGITAL OUT DIGITAL IN Ch Dynamics Insert to channels 1234 AES/EBU or SPDIF MIDI menu MIDI Ch Select MTC Type MMC Device ID MMC Communication Control Change Defeat L-R/GRP Control Change Mixer=1, Effectors 1=2 and Dynamics 30NDF 1 Closed-loop REC Mode:No No. 9 & 2=3 1 through 4 disabled DIGITAL IN B (option) assigned to 7&8 AUX SENDS (1-2 or 3-4) MONITOR OUTPUT (L and R) DIGITAL IN A assigned to two input channels) DIGITAL OUT A TM-D1000 Digital Mixer MIC (1/4) XLR (balanced) / MIX Mode:Yes MIDI OUT MIDI IN TDIF-1 A TDIF-1 System Menu Master Clock Select Direct Recall Defeat REMOTE CONT Function TDIF-1 A/B Word Length Meter Adjust Internal [48k ] Yes Snapshot Change [ up ] A:24bit ReleaseTime:30ms Hold Time:0s MIDI IN MIDI OUT / MMC-38 MIDI Interface controller REMOTE OUT REMOTE IN/SYNC IN DA-38 DTRS recorder controlled by MMC [. . . ] [. . . ]