User manual TASCAM US-2400 annexe 2

[. . . ] D00804300A DAW Controller USER'S GUIDE The following marking is located on the bottom of the unit: Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFETY PRECAUTIONS IMPORTANT (for U. K. [. . . ] Placing the US-2400 into one of the surface control modes is done when the unit is taken out of standby mode (with the POWER indicator pulsing). This setting is saved when the unit is powered off and on again, until changed in the same way. For details of how to use the US-2400 with Sonar, see "Sonar" on page 18. Mackie Control (Digital Performer) To set the Mackie Control emulation surface control mode for use with Digital Performer: 1 With the US-2400 in standby, press and hold the master SEL key and the AUX 3 keys together. 2 While holding down these keys, turn on the US-2400 using the POWER key. For details of how to use the US-2400 with Digital Performer, see "Digital Performer" on page 20. HUI To set the HUI emulation surface control mode (factory default). We recommend using this mode with Pro Tools: Mackie Control (Logic) To set the Mackie Control emulation surface control mode for use with Logic: 1 With the US-2400 in standby, press and hold the master SEL key and the AUX 1 keys together. 1 With the US-2400 in standby, press and hold the master SEL key and the AUX 4 keys together. 2 While holding down these keys, turn on the US-2400 using the POWER key. For details of how to use the US-2400 with Pro Tools, see "Pro Tools" on page 16. 2 While holding down these keys, turn on the US-2400 using the POWER key. For details of how to use the US-2400 with Logic, see "Logic" on page 22. Mackie Control (Sonar) To set the Mackie Control emulation surface control mode for use with Sonar: Native mode To set Native mode: 1 With the US-2400 in standby, press and hold the master SEL key and the AUX 5 keys together. 1 With the US-2400 in standby, press and hold the master SEL key and the AUX 2 keys together. 2 While holding down these keys, turn on the US-2400 using the POWER key. Release the SEL and AUX keys. 2 While holding down these keys, turn on the US-2400 using the POWER key. Release the SEL and AUX keys. Confirming the setting In the setup procedures described above, when the US-2400 has powered up, the appropriate AUX key (1 for HUI emulation, 2 for Mackie Control emulation (Sonar), 3 for Mackie Control emulation (DP), 4 for Mackie Control emulation (Logic) and 5 for Native mode) will flash three times to confirm the setting. Also note that when the unit is powered on, even when an emulation is not being selected, the AUX key corresponding to the currently-selected emulation will flash three times. TASCAM US-2400 Owner's Manual 9 3 ­ Selecting a Control Surface Mode Recognizing the US-2400 in your DAW MIDI port 1 MIDI port 2 MIDI port 3 MIDI port 1 MIDI port 4 Each bank of 8 faders on the US-2400 appears to the computer as one MIDI port, with the leftmost fader bank containing channels 1 through 8 also including the master section controls. The joystick appears on the fourth MIDI port. The following generalized steps should get you going on most DAWs, though some steps may not apply to your particular DAW software. For more detailed information on using the US-2400 with a particular DAW application, see the section entitled "Applications" on page 16. If your DAW is not one of the ones covered in the "Applications" section, please refer to your DAW's documentation to ensure that it supports multiple control surfaces, either HUI or Mackie Control and follow the basic steps described here. In the case of Mackie Control emulation, you may need to experiment with the three emulation modes provided by the US-2400 to find the one that properly controls your DAW's Aux sends and maps the US-2400's IN and OUT keys to useful functions. · Enable the US-2400 MIDI ports in your DAW's MIDI configuration window. Restarting the DAW software may be required for this change to take effect. · Open the Control Surface configuration window in your DAW software. · For DAWs that support multiple control surfaces as a single unified device, assign each US-2400 MIDI port to a separate control surface entry. Generally, you'll have to choose a control surface here that allows the DAW to find the US-2400 in a particular control surface mode. For example, if the US-2400 is emulating the HUI protocol, you would choose three HUI devices, each one on a different US2400 MIDI port. · Assign the ports left to right as follows: Port 1 represents faders 1­8; Port 2 represents faders 9­16; Port 3 represents faders 17­24; Port 4 represents the joystick. Note that Port 1 includes the master section controls. [. . . ] For example, faders, MUTE and SOLO keys and the transport controls will control those parameters in Digital Performer. Exceptions and specific details follow: Encoders When an AUX key is pressed, Aux sends are available. When CHAN is pressed, the encoders send generic MIDI controller messages as described in "MIDI Controller Mode" on page 12. 20 TASCAM US-2400 Owner's Manual 5 ­ Applications Transport keys The REW, F FWD, STOP, PLAY, and REC keys normally control the corresponding functions in Digital Performer. They additionally emulate the following Mackie Control commands when used with the F-KEY: · REW + F-KEY = Left Arrow · F FWD + F-KEY = Right Arrow · STOP + F-KEY = Down Arrow · PLAY + F-KEY = Up Arrow · REC + F-KEY = Zoom Other keys: · · · · IN = RTZ F-KEY + IN = CYCLE OUT = MARKER F-KEY + OUT = PUNCH Transport wheel When the SCRUB key is on (the indicator is lit), the transport wheel acts as a simple locator in Digital Performer. SEL keys Pressing a US-2400 SEL key alone selects that channel in Digital Performer. [. . . ]