User manual TEAC 5DV0010A

[. . . ] Turning the control to the right increases the volume. (Lower the volume before you play a disc to protect your hearing and speakers. ) LED indicator: The DVD-ROM drive features an LED indicator light on the front panel. Various operations are indicated as per the following table: TEAC DVD-ROM Installation Guide --1-- Rear Panel Operation At tray loading At tray eject During audio play During seek/data transfer At system/drive start-up Self-diagnosis error LED Indication green LED flashes green LED flashes green LED flashes green LED lights up (steady) green LED flashes green LED flashes eject button: Press this button to open or close the disc tray. (Some DVD and CD-ROM titles disable the manual eject button and rely on software commands to eject the disc. [. . . ] Remove your computer's cover, faceplate, or 5. 25-inch bay cover, as well as any mounting clips, screws, and retaining brackets. Note: If you (a) have a SCSI CD-RW or CD-ROM drive already installed in your system or (b) do not have any IDE CD-ROM or CD-RW drives installed in your system, continue with Step 4. If you already have an IDE CD-ROM or CD-RW drive installed in your system, skip step 4 and continue with Step 5. If you (a) have a SCSI CD-RW or CD-ROM drive installed in your system or (b) do not have any IDE CD-ROM or CD-RW drives installed in your system, do the following: 4a) Confirm that the jumper on the rear panel of the DVD-ROM drive is configured to its default setting of Master (see "TEAC 16X DVD-ROM Drive Installation Guide (this manual)" on page 3). 4b) Slide the DVD-ROM drive into an empty 5. 25" drive bay. Secure the drive using the included 3x5mm mounting screws. Warning: Do not use mounting screws longer than 3x5mm to secure the DVD-ROM drive or you may damage the unit. secure drive with 3x5mm screws 4c) Locate the secondary IDE connector on your system's motherboard and connect one end of the IDE interface cable to it. Note: The TEAC DVD-ROM kit does not include an IDE interface cable. If you need one, you can purchase it from your local computer store. TEAC DVD-ROM Installation Guide --4-- Installing the DVD-ROM Drive Be certain to connect Pin-1 of the interface cable to Pin-1 on the secondary IDE connector on the motherboard. (Pin-1 on an interface cable is usually designated by a color strip along one edge of the cable. Also, the interface ribbon cable connector may feature a tab on one side. Insert the cable so that the tab aligns with the notch on the drive's IDE interface connector. Do not use excessive force while trying to insert the cable into position. ) 4d) Connect the other end of the IDE interface ribbon cable to the interface connector on the rear panel of the DVD-ROM drive. (Skip Step 5 and proceed to Step 6. ) audio cable power cable pin 1 IDE interface ribbon cable 5. If you already have an IDE CD-ROM or CD-RW drive installed in your system, do the following: Typically, an IDE CD-ROM or CD-RW drive that is already installed in your system is connected to the secondary IDE motherboard connector, and is configured as a Master. In such cases, it is strongly recommended that you configure the TEAC 16X DVD-ROM drive as a Slave drive, then connect it to the same cable that currently hosts your installed CD-ROM or CD-RW drive. 5a) Set the jumper on the rear panel of the TEAC DVD-ROM drive to Slave (see "TEAC 16X DVD-ROM Drive Installation Guide (this manual)" on page 3). 5b) Slide the DVD-ROM drive into the empty 5. 25-inch drive bay. Secure the drive using 3x5mm mounting screws. Warning: Do not use mounting screws longer than 3x5mm to secure the DVD-ROM drive or you may damage the unit. 5c) Connect the DVD-ROM to the vacant middle connector on your CD-ROM/ CD-RW interface cable. (If your original cable does not have an available middle connector, you will need to acquire and install a standard IDE cable with three connectors. ) (Proceed to Step 6. ) 6. Connect one end of the included audio cable to the analog audio connector on the rear panel of the DVD-ROM drive, then connect the other end to your sound card. Note: There is no need to install this cable if an audio cable is already connected from your CD-ROM/CD-RW drive to the sound card. [. . . ] If not, click the Windows Start button, then select Run>D:setup. exe, where "D:" is the drive letter of the drive in which you inserted the PowerDVD CDROM. The Windows InstallShield Wizard displays the following panel: Click the "Next" button, then follow the on-screen InstallShield Wizard's instructions to complete the installation. Note: Once the software installation is completed, you will be prompted to execute the system diagnostic program. Select OK and make sure to enable DMA for the TEAC DV-516E and any other drive that supports this function. [. . . ]