User manual TEAC FT-3010

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TEAC FT-3010. We hope that this TEAC FT-3010 user guide will be useful to you.

Lastmanuals help download the user guide TEAC FT-3010.


Mode d'emploi TEAC FT-3010
Download
Manual abstract: user guide TEAC FT-3010

Detailed instructions for use are in the User's Guide.

[. . . ] NEVER try to open the unit by yourself for inspection or repair. Doing so may cause damage or operational failure and will void the warranty. Refer to this manual for installation, operation and maintenance procedures. If any repairs are required, contact your distributor or dealer from whom you purchased the unit. [. . . ] Precautions during placement: When installing the tape drive unit in the host computer horizontally, the LED on the front panel will be on the left side. When installing the tape drive unit vertically the LED on the front panel can be either above or below the opening for the tape cartridge. Avoid placing the unit (or host computer) in direct sunlight or near heating apparatus; place the unit in a clean moisture-free environment. Do NOT apply solvents such as thinner, benzene, or alcohol to the unit, as these may blemish the surface of the drive. When cleaning the drive, wipe off dirt using a soft dust-free cloth. If the tape drive unit does not operate normally even after being connected properly, contact the representative from whom you purchased the unit or our Technical Support number. If problems arise, and you need to take or send the unit to your place of purchase, please reuse the original packing materials. Do NOT vibrate or apply any shocks to the drive (or the host computer). KIT DESCRIPTION Your tape drive Kit comes complete with: (1) Tape drive unit (2) Tape Hardware Installation Guide (3) Arcada Backup Software User Guide (4) Registration card (5) Arcada Backup software program disks for DOS, Windows 3. x and Windows 95 (6) Tape drive interface data cable (7) Mounting screws (8) Mounting brackets for mounting in a 5 l/4" bay + Note: If all items are not contained in your Kit, please return it to the dealer you purchased it from. CONTROLS, CONNECTIONS AND FUNCTIONS Tape800/1600 ON/BUSY LED indicator Tape cartridge insertion window Front View TOOLS YOU MAY NEED Depending on the design of your computer, you may need the following tools to complete the installation. 0 A flat blade screwdriver 0 A Phillips screwdriver 0 Needle-nosed pliers Fig. 1 Strap switch - Preset Factory Setting Please vertfy the device configuration jumpers are set as shown below. Device confiauration jumpers The jumpers are preset at factory for all PC configurations. DO NOT change any of the default settings. Power connector Rear View Interface connector Pl;rl #l Fig. 10 Plug the remaining end of the tape drive interface data cable into the floppy controller card. Orient the color stripe as noted in Step 8. Find any unused power cable inside your computer and plug it into the back of the tape drive unit. The power connector is keyed so that you can only plug it in one way. Press firmly until the connector snaps into place. Secure and ground the tape drive unit in the bay, if necessary. + Note: You do not need to change your CMOS settings. Follow the instructions inside the Arcada Backup User Guide, for installing the tape backup software, before you attempt to use your tape drive. t Tape Ejection 1. Hold tape and firmly remove it straight out from drive. + Caution: To prevent the tape from becoming excessively loose and causing damage: DO NOT eject a tape while it is running and the LED is on. Write protection tab DO NOT switch the power off while a tape is running. [. . . ] Write protection tab DO NOT switch the power off while a tape is running. After ejection, store the tape in a tape carrying case until it is to be used again. Insert this edde into tape drive -6- -7- . HARDWARE INSTALLATION GUIDE SPECIFICATIONS Tape1600 Model: Recommended Media: Compressed: Uncompressed: Tape Format: Downward Read Compatibiltity: Speed: Data Transfer Rats: Interface: MTBk Dimensions: Weight: FT-301 OTR Travan TR-2 1. 6G8 EOOMB QIC-301 O-MC QIC-80, 1X-40 Tape800 FT3008TR Travan TA-1 EJOOMB 400MB QIC-EO-MC QIC40 Up to 95M8 per minute Dual Speed: SOOKbps and1 Mbps* Floppy 119, 000 POH 4YWl x IYHI x 5. 7"IDl . 99 Ibs. i 1 Mbps reqwes high-speed c~ntmller TAPE MEDIA COMPATIBILITY Tape1600 Minicartridge Compatibility Media Type: Format: Compressed 2:i Uncompressed: Tape Length: Brand Name: Jravan TR-2 QIQ 3010 1. 6GB 800MB 750 ft. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TEAC FT-3010

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TEAC FT-3010 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag