User manual TEAC TD0030A

[. . . ] 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] To stop playback manually, slightly lift the tone arm using the cue lever and return it to the tone arm holder. 8 tone arm 7 7 Move the tone arm gently to the edge of the record (or cue lever the starting point of a track). The turntable will begin to turn. 8 Gently lower the tone arm by slowly releasing the cue lever. You can lower the tone arm manually if the cue lever has not been raised. cue lever < Playing records with the dust cover down will prevent dust from settling on the turntable. Please do not place anything on top of the turntable cover, especially while playing a record. 14 Listening to a CD 1 1 5 3 24 1 Press the CD button. 4 Press the OPEN/CLOSE button (L) to close the tray. "--" blinks for a few seconds. When no disc is set, "nOdISC" appears on the display. < It takes a few seconds for the unit to load the disc. Wait until the total number of the tracks and the total play time of the disc are displayed. disc type indicator 2 Press the OPEN/CLOSE button (L). total number of the tracks 3 Place a disc on the tray with the printed label face up. total play time of the disc < The disc type indicator shows the type of disc currently loaded. CD: A commercial pre-recorded CD CD-R: A finalized CD-R CD-RW: A finalized CD-RW NO TOC CD-R: A CD-R which has yet to be finalized NO TOC CD-RW: A CD-RW which has yet to be finalized blank: No disc or unreadable disc 5 Press the PLAY button (y) to start playback. < Never place more than one disc on the tray. < The disc must be placed in the center of the disc tray. If the disc is not correctly loaded, it may not be possible to open the tray again once it has closed, so you should ensure the disc is always centered on the tray. < Do not force the tray by hand during opening and closing operations. Disc playback starts from the first track, and the PLAY indicator (y) lights on the display. < Insert a disc and select "CD" before beginning programming. < Shuffle playback does not work during programmed playback. < Programmed playback works with finalized discs only. 3 Press the PROGRAM button. 1 Press the PROGRAM button in the stop mode. The track is programmed, and "P-02" is displayed. Repeat step 2 and 3 to program more tracks. < To cancel the program mode, press the STOP button (H). "PROGRAM" indicator blinks, and "P-01" appears on the display. 4 When the selection of track numbers has been finished, press the PLAY button (y) to start program playback. 2 Press the MUSIC SKIP button (. or /) to select a track. track number 18 Before Recording To check the programmed order In the stop mode, press the MUSIC SKIP button repeatedly to show the track numbers that have been stored in memory. Before you start recording, make sure that you understand the following points: < The unit requires Digital Audio CD-R or CD-RW media for recording. Computer CD-R or CD-RW discs do not work with this unit. < Once you have recorded on a CD-R disc, the data cannot be erased from it. < You can add tracks to an unfinalized recordable disc. Once finalized, a CD-R disc is "fixed" and behaves in the same way as a CD. [. . . ] P-** Program number UN FIN Unfinalize the CD-RW disc. Error Messages D FULL, OPFULL There is no space on the disc, or no more tracks are available. D DISC Discs designed for computer systems cannot be used for recording. Use the discs bearing "DIGITAL AUDIO" mark. Err ** An error occurred within the unit. [. . . ]