User manual TEC FS-1535 PROGRAMMING MANUAL

[. . . ] TEC Electronic Cash Register FS-1535 SERIES Programming Manual Document No. EO3-11104 Original (Revised Sep. , 2003 ) PRINTED IN JAPAN EO3-11104 TABLE OF CONTENTS Page 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 1 1. 1 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 1 2. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- 1 3. [. . . ] |Tax Code| [#/NS] 1 digit (1 to 4) 1: Tax 1, 2: Tax 2, 3: Tax 3, 4: Tax 4 First set all the breaks up to the "A" Break entry, and then depress the [ST] key as shown in TYPE 1. |Tax Rate applied when exceeding the "A" Break amount| [AT/TL] (0. 00% to 99. 99%; Use the [. ] key when a decimal point is contained. The fraction of the amount resulting from this % rate calculation will be rounded off. ) [#/NS] (to complete this tax programming) TYPE 3: TAX 1 % RATE ONLY 12 [#/NS] |Tax Code| [#/NS] 0 [X/TIME] [ST] 1 digit (1 to 4) 1: Tax 1, 2: Tax 2, 3: Tax 3, 4: Tax 4 |Tax Rate| [AT/TL] (The description for the Tax Rate in TYPE 2 is also applied to this case. ) [#/NS] NOTES: 1. For Tax 2, Tax 3, and Tax 4 Table Programming, follow the same procedure in TYPE 1, 2, and 3 as shown the above. If multiple tax tables are programmed, the Tax 1 table must be set first, and then Tax 2, Tax 3, and Tax 4. The Tax 1 table setting will automatically reset all of the old Tax 1, 2, 3, and 4 tables if they have been programmed. Do not depress the [ST] key over twice in one tax table programming. Up to 99 breaks can be entered for Tax 1 to Tax 4 tables together. 4-38 4. PROGRAMMING OPERATIONS EO3-11104 4. 18 VAT or Add-on Tax Rate Setting (Submode 12) Example 1) TAX 1 FULL BREAKS Tax Table Tax Levied Amount Range $0. 00 to $0. 10 0¢ $0. 11 to $0. 22 1¢ $0. 23 to $0. 39 2¢ $0. 40 to $0. 56 3¢ $0. 57 to $0. 73 4¢ $0. 74 to $0. 90 5¢ $0. 91 to $1. 08 6¢ ---- "A" Break $1. 09 to $1. 24 7¢ $1. 25 to $1. 41 8¢ $1. 42 to $1. 58 9¢ $1. 59 to $1. 74 10¢ $1. 75 to $1. 92 11¢ $1. 93 to $2. 08 12¢ ---- "B" Break Key Operation Control Lock: SET, Enter 12 and depress the [#/NS] key. 10 [X/TIME] 22 [X/TIME] 39 [X/TIME] 56 [X/TIME] 73 [X/TIME] 90 [X/TIME] 108 [X/TIME] [ST] 124 [X/TIME] 141 [X/TIME] 158 [X/TIME] 174 [X/TIME] 192 [X/TIME] 208 [X/TIME] [#/NS] 24-01-2003 PRG 01-01 -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 -12 -13 0025 #0000 12 10 22 39 56 73 90 108 ST 124 141 158 174 192 208 14:45TM Example 2) TAX 2 COMBINATION OF NON-CYCLIC BREAKS AND % RATE Tax Table Tax Levied Amount Range $0. 00 to $0. 09 0¢ $0. 10 to $0. 29 1¢ $0. 30 to $0. 59 2¢ $0. 60 to $0. 84 3¢ $0. 85 to $1. 12 4¢ ---- "A" Break 5% is applied to any amount exceeding the "A" Break. Key Operation Control Lock: SET, Enter 12 and depress the [#/NS] key. 2 [#/NS] 9 [X/TIME] 29 [X/TIME] 59 [X/TIME] 84 [X/TIME] 112 [X/TIME] [ST] 5 [AT/TL] [#/NS] 24-01-2003 PRG 02-01 -02 -03 -04 -05 02-01 0026 #0000 12 9 29 59 84 112 ST 5. 00 14:48TM Example 3) TAX 10% RATE ONLY Tax Table 10% is applied to any sale amount. Key Operation Control Lock: SET, Enter 12, and depress the [#/NS] key. 3 [#/NS] 0 [X/TIME] [ST] 10 [AT/TL] [#/NS] 24-01-2003 PRG 03-01 03-01 0027 #0000 12 0 ST 10. 00 14:50TM 4-39 4. PROGRAMMING OPERATIONS EO3-11104 4. 19 Department Group Name Programming (Submode 13) 4. 19 Department Group Name Programming (Submode 13) The Name of Department Group can be programmed here, which Department has already been linked to a Group in 4. 10 Department Table Programming (Submode 3). CONDITION OPERATION Anytime outside a sale Control Lock: SET Repeat for other Groups. 9 groups) 13 [#/NS] |Group Code| [#/NS] 2 digits (01 to 09) Character entry [AT/TL] Max. 18 characters (See NOTE below. ) [#/NS] NOTE: Entering 2 digits of numeric code provides an alphanumeric character of Department Group Name. Therefore, odd number of numeric digit entry will cause an error. When less than 36 digits of numeric data are entered, this ECR uses space code entry. If a Department Group Name includes spaces at the beginning, entering space code is required at the beginning of data entry. For the Department Group name, up to 18 regular-sized or 9 double-sized characters can be entered. Also a combination of both types can be entered. [. . . ] Anytime outside a sale CONDITION OPERATION 90 [ST] Control Lock: X or Z Repeat for other PLUs. |PLU Code| [PLU] |Stock Quantity| (0. 001~9999. 999) [RA/LOAN] (When adding the stock quantity. ) [ST] [PO/PICK-UP] (When subtracting the stock quantity. ) NOTE: PLU programming should be done before this operation. Example) To change the stock quantity of the PLU00000000000001 (BEEF STEAK: current stock quantity 50). Key Operation: Control Lock: X or Z, Enter 90 and depress the [ST] key. 1 (PLU Code) [PLU] 20 (Stock Quantity) [RA/LOAN] (When adding the stock quantity. ) [ST] (To complete this submode. ) 24-01-2003 X BEEF STEAK 0058 #1234 90 70 15:50TM 4-84 5. PROGRAMMED DATA VERIFICATION EO3-11104 5. 1 Programmed Data Verification in BLIND Mode 5. [. . . ]