User manual TECHNICS RS-B10

[. . . ] IN NO EVENT SHALL TECHNICS BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT. Requests This Operation manual has been carefully prepared for your easy understanding. However, please do not hesitate to contact a distributor in your district or our office if you have any inquiry. Description contained in this Operation manual are subject to change without notice for improvement. It is also necessary to keep this Operation manual on hand. [. . . ] > [JV5-01] width : mm 2 Press the [ST. MAINT] key and press the [ENTER] key. When [CARRIAGE OUT] is displayed, press the [ENTER] key. Then the carriage moves to above the platen. ST. MAINTENANCE CARRIAGE OUT <ent> 4-7 4 Daily Maintenance 3 Open the right maintenance cover. 4 Pull out the wiper by holding the projections at both ends. 5 Remove the ink from the wiper and the bracket using a cotton swab dampened with the cleaning solution. Replace the wiper with a new one if it is badly soiled or curled. To replace the wiper, terminate the work instructed here first and then follow the wiper replacement procedure. (See 4-47) 4-8 Cleaning the wiper and ink caps [CARRIAGE OUT] 6 After cleaning the wiper, install it in position by holding the projections at both ends. Be careful of the direction of the wiper. 7 Wipe off ink or dirt adhering to the rubbers of the caps and the wiper cover using a cotton swab dampened with the cleaning solution. Be careful not to leave lint of the cotton swab. Lint may cause printing failure. Ink cap 8 Close the maintenance cover, and press the [ENTER] key. After performing the initial operation, the printer returns to LOCAL mode. Being Initialized :end PLEASE WAIT ST. MAINTENANCE COMPLETED 4-9 4 Daily Maintenance Cleaning the nozzle [NOZZLE WASH] Perform cleaning of the nozzles in the heads to prevent them being clogged with coagulated ink. Be sure to wear the supplied goggle and gloves. The ink contains an organic solvent. If ink settles on your skin or gets in your eyes, immediately and completely wash them off with water. Then, consult a doctor as soon as possible. (When solvent ink is used) If nozzle clogging cannot be corrected even after repeating the cleaning procedure described here several times, execute the [FILL UP INK] (Refer to "If nozzles cannot be unclogged [FILL UP INK] (p. 3-31)" ) , [DISCHARGE&WASH] (Refer to "[DISCHARGE&WASH] (p. 5-6)" ) functions. If the remedies instructed here do not work, contact your dealer or an office of TECHNICS. When the [DISWAY WASH] function is executed, there may be a case where the cleaning liquid keeps staying in the caps without flowing out. In such a case, the pump may be clogged. If the pump is clogged, contact your dealer or a sales office of TECHNICS. STEPS: 1 Make sure that the printer is in LOCAL mode, and then press the [ST. MAINT] key. If it is in REMOTE mode, press the [REMOTE] key. L. > [JV5-01] width : mm ST. MAINTENANCE CARRIAGE OUT <ent> 2 Select [DISWAY WASH] by pressing the [ key. 3 times ] key three times and press the [ENTER] The carriage will come out of the capping station. Idle suction is performed in cycles of 5-second suction followed by 10-second pause. ST. MAINTENANCE DISWAY WASH <ent> If there is a problem with the waste ink tank, the display will show either of the following messages. Follow the displayed instructions to restore the normal conditions. No waste ink tank, or a tank is FULL. <ENT>keyHIT is after theTANK set or exchg Replace a waste ink tank. <ENT>keyHIT is after the TANK exchange. 4-13 4 Daily Maintenance 3 Open the right maintenance cover. 4 Take the cleaning solution into the dropper. During a pause of idle suction, drop cleaning liquid into a cap until just before it starts overflowing from the cap. Repeat dropping the cleaning liquid into each of the other caps the same way. Ink cap 5 Close the maintenance cover and press the [ENTER] key. Fill a cal while absorption stops. ST. MAINTENANCE COMPLETED : ent 6 The printer performs idle suction for 30 seconds, and after initial operation, returns to LOCAL mode. Being Initialized PLEASE WAIT L. [. . . ] This graphic is used together with the icon . 6-33 6 Operation for Functions Functions related to the cutter When the media is to be cut at a desired position Cut the media at any desired position without using the [AUTO CUT] function. (Refer to "Cutting the media after completion of printing (p. 3-41)" ) L. > [JV5-01] width : mm ORIGIN SET UP Move the carriage and media using JOG keys so that the carriage is located at the position where cutting is to be started. When [HEAD GAP] has been set to 4. 1 mm or more, media cutting cannot be performed. MEDIA CUT <ENT> MEDIA CUTTING PLEASE WAIT The media is cut. [. . . ]