User manual TECHNICS SC-EH780

[. . . ] System Component Operating Instructions Model No. SC-EH780 SC-EH680 SC-EH580 H SLEEP PROGRAM CANCEL 1 2 3 DISC 4 5 6 j/-/-- 7 8 9 0 TEST UPRO LOGIC SUPER SRND 3D AI EQ CH SELECT AV EFFECT SUPER SOUND EQ DIGITAL S. WOOFER VCR/AUX/ TAPE/ 6CH INPUT DECK 1/2 CD TUNER/ BAND //g » ¤ MUTING M N VOLUME µ The illustration shows SC-EH780 for the United Kingdom and Eastern Europe. Note "EB" on the outer packaging indicates the United Kingdom. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. EB EP EE GN RQT6301-B Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. [. . . ] There are 39 channels available for presetting. A » Automatic presetting Do the following once each for FM and AM. Preparation: Tune to the frequency presetting is to begin at (á page 17). TUNING MODE SET Hold down [SET]. Release the button when "AUTO MEMORY" appears. The tuner presets all the stations it can receive into the channels in ascending order. FM stations are preset into channels 1 to 39, and AM stations are preset into channels 21 to 39. "SET OK" is shown when presetting is complete and the last station to be preset is played. "ERROR" is displayed if the tuner doesn't receive any stations. Do presetting manually if this happens (see below). MHz A SET B 2 SET Note AM stations replace any FM channels that were preset in channels 21 to 39. B » Manual presetting Preset the stations one at a time. Press [TUNING (X or W)] to select a channel. Press [SET]. 3? TUNING @ Basic operations 4 SET The station occupying a channel is erased if another station is preset in that channel. C C » Selecting channels H SLEEP PROGRAM CANCEL Í 1 2 3 DISC Preparation: Press [ê] to turn the unit on. 4 5 6 j/-/-- 7 8 9 0 2 On the remote control TEST UPRO LOGIC SUPER SRND 3D AI 1 2 Press [TUNER/BAND]. Press the numbered buttons to select the channel. For channels 1 to 9 press the corresponding number. For channels 10 or over press [L/-/--], then the two digits. To select channel 21: [L/-/--]>[2]>[1] EQ CH SELECT AV EFFECT SUPER SOUND EQ DIGITAL S. WOOFER VCR/AUX/ TAPE/ 6CH INPUT DECK 1/2 CD TUNER/ BAND 2/; » ¤ 1 3 3 Adjust the volume. MUTING 4 5 VOLUME µ On the main unit 1 Select "PRESET" with [TUNING MODE]. 2 Press [TUNING (X or W)] to select the channel. 1 2 1 4 7 TUNER/ BAND 2 5 8 3 6 9 j/-/-- Preset channel 0 18 RQT6301 3 VOLUME µ Cassette tapes See page 39 for tape selection. Preparation: Press [ê/I] to turn the unit on. Í/I 5 DECK 1/2 6, 5 1 2 3 Press [< OPEN] on deck 1 or deck 2 and insert the cassette. Close the holder by hand. Press [DOLBY NR] to select Dolby NR on ("ëNR" appears) or off. Press [REV MODE] to select the reverse mode. Each time you press the button: b: One side is played. f: Both sides are played 8 times each. 4 Press ["] (reverse side) or [!] (forward side). Play begins and the indicator changes to green. 1 DECK 1 4 231 DECK 2 Forward side Tape facing down 5 Adjust the volume. 1 2 3 4 <OPEN To stop the tape Press [º]. [A] To change the deck to be used Press [DECK 1/2] to select the deck you want to play. To listen to 2 tapes consecutively DOLBY NR ÎNR 1 Insert a tape into each deck and select "f". Both tapes will be played 8 times each. » Finding a place on a tape B REV MODE ÎNR 1 Press [6] or [5] while the tape is stopped. To find the beginning of a track (TPS: Tape program sensor) Press [6] or [5] during play. Play resumes from the beginning. " Tape direction ³Each deck's play direction is stored in the system's memory. ³You can fast-forward or rewind the tape while you are playing or recording a tape in another deck. Press [DECK 1/2] to switch to the deck not playing, and then press [6] or [5]. After the above operation, be sure to press [DECK 1/2] to reselect the deck playing. Note TPS may not operate correctly in the following situations: If the interval between tracks is less than 4 seconds. If there are silent parts within tracks. [. . . ] "DECK CHANGE TAPE" is displayed during "One touch editing". If the erasure prevention tabs have been removed, cover the holes with adhesive tape. L When there is a television set nearby The picture on the TV disappears or stripes appear on the screen. The location and orientation of the antenna are incorrect. If you are using an indoor antenna, change to an outdoor antenna. [. . . ]