User manual TECHNICS SL-P1300

[. . . ] Use numbers indicated in parentheses when asking for replacements parts. (Only for U. S. A. ) To order accessories contact 1-800-332-5368 or the website (http://www. panasonic. com). (SFPWG17201K) Table of contents Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ¡Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ¡Consult the dealer or an experienced radio/TV technician for help. Any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3 RQT7018 Features A masterpiece amongst turntables with a worldwide reputation. Highly accurate turntable speed maintained continuously with a quartz pitch control. ·The pitch can be varied throughout the range maintaining perfect accuracy. ·Pitch can be instantly reset to the rated speed (33 1/3 or 45 r/min) with the reset button. Controls The direct drive produces high torque. ·Wow and flutter below 0. 01 %. Starting torque of 1. 5 kg-cm enabling the turntable to reach 33 1/3 r/min in 0. 7 seconds. ·Smooth stops are achieved with a fully electronic braking system. The braking speed can be adjusted with the brake speed control knob. -8 6 4 2 +8 2 4 6 +8 Tone arm with gimbal suspension ·Using the balance weight control measurement units on the tone arm, you can quickly change stylus pressure settings to the appropriate pressure. ·Stylus skipping can be reduced using horizontal weight control for scratch play. ·Confirm the wattage of AC outlets on amplifiers and receivers before using them for this unit. This unit consumes 13. 5 W. To household AC outlet 1 1 Earth lead Stereo connection cable 2 5 RQT7018 Connections and installation Connecting to an Audio Mixer (not included) ·Disconnect all units from the power source before making any connections. ·Reconnect the AC power supply cord after all other connections are complete. Attach the cartridge to the tone arm you are using. Turn the balance weight control to the setting you previously used to balance the weight including cartridge. Turn the stylus pressure control dial to the setting you previously used to balance the weight including cartridge. Tone arm height 1. Release the arm lock. Released 1 3 Locked 2. Adjust the arm height. ·Adjust the ring using the chart below as reference so the arm height matches the indicated height of the cartridge. Measurements are marked on the arm height control ring in 0. 5 millimeter intervals. Balance weight measurement units Index line Arm height control ring Cartridge height (H) in millimeters Height control position 0 1 2 3 4 5 6 Anti-skating Adjust the dial to the same value as the stylus pressure control when playing normal music. For scratch play Adjust the control to reduce skipping. 17 18 19 20 21 22 23 ·If you do not know the height of your cartridge, rest the stylus on a record and adjust the height control until the tone arm and record are parallel. Tone arm and record parallel. Armlift height Preparation 1. Take off the stylus cover and release the arm clamp. 3. [. . . ] Safety check--After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition. Thoroughly clean dust off the stylus and record. ·Use a soft brush to clean the stylus. ·Use a good quality record cleaner to keep your records clean. Head shell terminals Wipe the head shell terminals occasionally. Use a soft cloth. Turn the amplifier off before fitting or removing the head shell. ·Damage to your speakers can occur if the head shell is moved while the volume is turned up. [. . . ]