User manual TECHNOLINE BC-700 QUICK REFERENCE

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. [. . . ] After changing channels or modes, this is no longer possible. 4. 5. 4 Programming a Repeater-Access Function Setting The "Repeater-Access" function is to set the desired shift and tone parameters to the current operating frequency by just 2 key-touches. Please set the parameters to be applied to the Repeater-Access function here. Enter the Memory mode (by pressing the key if necessary). Set the most commonly used Repeater-Access parameters by referring to "RepeaterAccess" (page 40). The parameters that can be programmed in this memory are marked * in the chart 4. 5. 5 on the next page. By activating the Repeater-Access function these settings are applied to the operating frequency regardless of the VFO/Memory/CALL modes, by temporary replacing the current parameters. After programming is completed, press the FUNC key then press the while MrpALL is displayed to store the edited parameters. Rotate the dial to operate in the Memory mode by selecting channels or press the key for VFO mode operation. NOTE: · You can not communicate in the channel. · The channel is skipped during scanning. You can not delete or convert this memory to other purposes. 26 4. Basic Operation 4. 5. 5 Programmable Parameters in Memory Channels The following parameters can be stored in each of the memory channels. (Low power output) · is displayed with on the power meter. (Middle power output) · Nothing is displayed with on the power meter. (High power output) The initial setting is low power. IMPORTANT NOTE: The output level can't be altered while transmitting. 4 29 5. Useful Functions 5. Useful Functions 5. 1 Scan Modes The scan function automatically searches the receiving signals. There are 2 modes for scan-resume condition. · Busy Scan: The scan stops when a signal is detected, stays until the signal is gone then resumes scanning. · Timer Scan: The scan stops when a signal is detected, and resumes scanning after 5 seconds regardless of receiving status. During scanning, the 1MHz decimal point ( ) on the frequency display flashes. Press any key other than the MONI key to stop scanning. Scanning starts in the direction of the last dial operation (up or down). 5 NOTE: Please refer to the Set mode to switch the setting between Timer and Busy scan modes (page 42). 5. 1. 1 VFO-Scan 1. [. . . ] Please charge the pack completely before use. Available Battery Packs for DJ-175 EBP-71 EBP-72 Li-ion Battery Pack (DC 7. 4V 1200mAh) Ni-MH Battery Pack (DC 7. 2V 700mAh) Charging Battery Packs Refer to the chart below for the combination of the proper battery pack and charger. The indicates the usable combination, (* hrs) means the approximate time necessary to full charge the empty pack. Battery Packs Chargers EDC-164 EDC-165 Li-ion Battery Pack EBP-71 (2. 5hrs) Ni-MH Battery Pack EBP-72 (10hrs) 10 52 10. Maintenance and Reference 10. 3. 2 Using the Chargers Caution Please also read the "Warning" (page 4 of this manual) and the safety instruction that is included in the accessories' package before operating for your safety. Charging with the EDC-165 (Trickle Charger) Please make sure that following items are included in the package. · EDC-165T: EDC-165 basket, EDC-146 adapter (AC 120V), insulation sheet · EDC-165E: EDC-165 basket, EDC-147 adapter (AC 230V), insulation sheet · EDC-165UK: EDC-165 basket, EDC-148 adapter (AC 230V), insulation sheet *Standard accessories may vary depending on the models you have purchased. Connect the AC adapter plug to the DC-IN jack on the back of the basket. [. . . ]