User manual TECHWOOD PL66

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11625 Columbia Center Drive Suite 100 Dallas, Texas 75229 972-243-5602 weltonusa. com WELTON U. S. A. SECTION 2 NOTE: Solid lines Dotted lines AUDIO & VIDEO CONNECTIONS = suggested method of connection = alternate method of connection TV CABLE BOX ANTENNA OUT COMPONENT VIDEO IN ANTENNA IN VIDEO IN S-VIDEO IN AUDIO OUT CD RECORDER OPTICAL AUDIO IN SPEAKERS 8 REAR CENTER FRONT AUDIO OUT TAPE IN TV OUT VCR IN SAT AUX L R ANTENNA AM GND VIDEO S-VIDEO OUT MONITOR OUT FM DVD OPTICAL DIGITAL OUT SAT IN + R L R L + - OUT IN IN SUB WOOFER VCR Cr SAT Cb Y C O M P O N E N T V I D E O O U T PRE-OUT AUDIO OUT VIDEO OUT AUDIO IN AUDIO OUT VIDEO OUT VIDEO IN OPTICAL AUDIO OUT SATELLITE SYSTEM VCR IMPORTANT NOTE: When connecting components to the PL66 make sure that the AUDIO/VIDEO cables are properly connected (white audio plugs to white audio jacks, red audio plugs to red audio jacks and yellow video plugs to yellow video jacks). SECTION 3 DISC 1 DISC 2 DISC 3 PLAYING THE RADIO PL66 500 WATT 3 DVD HOME THEATER SYSTEM DISC 1 DISC 2 DISC 3 REMOTE SENSOR NIGHT MODE STAND BY DIMMER DISC SKIP/ TUNING MODE FUNCTION DTS DOLBY DIGITAL SURROUND MODE STEREO VOLUME NIGHT MODE POWER STANDBY/ON SLEEP TUNING/PRESET FM MODE BAND MEMORY PHONES DOWN UP STEPS 1 2 1 7 4 4 6 7 3 6 5 2 5 Press the power button on the front of the PL66 or on the remote. Turn the FUNCTION knob on the front of the PL66 until AM or FM appears on the display or press the TUNER button on the remote. NOTE: The TUNER button on the remote must be pressed in order to control the TUNER functions with the remote. Press the BAND button on the front of the PL66 or on the remote to select AM or FM. [. . . ] Repeatedly press TUNING/PRESET in the desired station. or to tune To change the frequency by one step, press TUNING/PRESET or quickly (less than half a second). To tune to the next clear frequency, hold down TUNING/ or , then release the button. The PRESET system automatically tunes to the next strong station. When MEMO goes off, press MEMORY again ( MEMO flashes again). Repeatedly press TUNING/PRESET or until the desired memory location number appears. Or use the number keypad to enter the desired memory location number. Repeat Steps 1­5 to memorize other stations (up to 30 stations for each band). If you store a new station on a memory number in which a station is stored, the old station is cleared. USING THE CD PLAYER You can use the receiver's 3-DVD changer to listen to audio CDs. Important: You can only use audio CDs with the reciever. CD-ROM, CD-G, photo CD, and CD-i discs cannot be played on this player. Note: Dolby Digital and DTS modes can be operateble with Disc encoded with them. USING NIGHT MODE You can use Night Mode to compress large dynamic ranges, resulting in "quieter" explosions and other loud sounds in movies. The Night Mode feature adjusts the dynamic range so 12 REMOTE CONTROL OPERATION A QUICK LOOK AT THE REMOTE CONTROL SURROUND -- Repeatedly press to change the surround mode to PRO LOGIC, THEATER, HALL, or STADIUM. Note: SURROUND works to change to stereo. MUTE -- Press to immediately stifle the sound level. MUTE appears on the receiver's display panel. To restore the sound, press again. TEST TONE -- Turns on or off the test tone function in DTS, DOLBY DIGITAL, or PRO LOGIC mode. The test tone is output from Front L speaker, Center speaker, Front R speaker, Surround R speaker, Surround L speaker, (Subwoofer speaker when Subwoofer is on). TONE -- Lets you adjust the low frequency level (BASS) with or . You can also adjust high frequency level (TREBLE) with or . SLEEP -- Press to set the sleep time. PRESET ­ / + -- During AM or FM reception, you can scan through other frequencies or select the preset numbers. BAND/ -- Selects AM or FM band while using the tuner. TUNING MODE -- selects and deselects preset mode. FM MODE -- Selects FM mono or stereo mode. MEMORY -- Press to memorize the desired station frequency. OPERATING RANGE OF THE REMOTE CONTROL The remote control may not work properly if: · There are obstacles between the remote control and the receiver's remote sensor. · Direct sunlight or fluorescent light is shining onto the remote sensor. · The receiver is located near a device that is emitting infrared rays. · The receiver is operated simultaneously with another infrared remote control. 13 SETTING UP THE SURROUND SOUND SYSTEM You can use your Home Theater Audio System as soon as you take it out of the packaging. [. . . ] Source being played is not recorded or broadcast in surround sound or stereo. One or more rear speaker wires is not making good contact, Place this product as far away as possible from electric devices with interference. After turning off the power and then turning it on again, reduce the volume or change to the correct 6-ohm speakers. Check all speakers for correct polarity. [. . . ]