User manual TECUMSEH HMXL70-132503

[. . . ] HMXL70-132503 Page 1 of 8 Engine Parts List #1 Ref # 1 3 4 4A 5 6 6 6 7 8B 8 8A 9 9 9 9A 9A 9A 10 11 11 11 17 18 18A 19 19A 20 21 22 23 24 25 26 27 33 33A 34 35 36 37 38 39 40 41 42 43 49 Part Number 35488 27642 35319 35400 27652 29536 35256A 35326 650561 33245 35442B 29783 34552 34553 34554 34329A 34330A 34331A 27888 34332 34333 34334 35373A 35374 32590 650908 650882 34034 35375 33273A 650128 35262 35376 35377 35319 30699C 30699B 30700 650494 29642 31845 30588A 30590A 29193 35378 33369 650836 29916 Qty Description Cylinder (Incl. 3, 4, 4A, 5)(3-1/8")(CI liner) Plug, Pipe (1/4-18) Seal, Oil Bushing, Crankshaft Pin, Dowel Blower Housing Baffle (No knock-out for electric start) (Use as required) Blower Housing Baffle (With knock-out for electricstart) (Use as required) Baffle, Blower housing Screw, 1/4-20 x 5/8" HMXL70-132503 PageGear8 Crankshaft 2 of (Used on early produc tion) Engine Parts List #1 Crankshaft Crankshaft Gear Pin (Used on early pr od. ) Piston, Pin & Ring Set (Std. ) (3-1/8" ) Piston, Pin & Ring Set (. 010" OS) Piston, Pin & Ring Set (. 020" OS) Piston & Pin Ass'y. (Std. )(Incl. 10)(3 -1/8") Piston & Pin Ass'y. [. . . ] Screw, 8-32 x 5/16" Locknut, 8-32 Screw, 1/4-20 x 1-11/16" Screw, 1/4-20 x 1-3/16" Dipstick (Incl. 59) * Gasket, Oil fill Exhaust Valve (Std. ) (Incl. 70) Exhaust Valve (1/32" OS) (Incl. 70) Intake Valve of 8 Engine Parts List #1 Intake Valve (1/32" OS) (Incl. 70) Seal, Assy. , Intake valve Cap, Upper valve spring Spring, Valve Cap, Lower valve spring Key, Flywheel Clip, Fuel line Retainer, Wire Flywheel Washer, Lock Nut, Hex, 5/8-18 Stud, Solid State mounting Solid State Assy. Cover, Spark plug (Use as required) Screw, Torx T-15, 10-24 x 1" Ground Wire * Gasket, Cylinder head Head, Cylinder Screw, 5/16-18 x 1-3/4" (Use as requi red) Screw, 5/16-18 x 1-1/2" (Use as required, but do notuse No. 650691 washer. ) Screw, 5/16-18 x 1-5/8" (Use as required) (Can use No. 650691 washer. ) Resistor Spark Plug (RJ-8C) Washer (Use as req. ) (Do not use w/60 21A) Screw, 5/16-18 x 1-3/4" (Use as requi red) Washer, Belleville Screw, 5/16-18 x 2" * Gasket, Breather Body, Breather Element, Breather Cover, Breather Screw, 10-24 x 1/2" Nut, Whiz lock, 1/4-28 Gasket, Carburetor Pipe, Intake Screw, Torx T-30, 5/16-18 x 1-1/8" * Gasket, Intake Blower Housing (For electric starter) Control Bracket (Incl. 134, 135, 136 & 138) Spring, Compression Screw, 5-40 x 7/16" Qty Ref # 136 137 138 139 141 142 144 145 146 153 154 158 168 169 169 169 169 170 171 172 173 174 175 Part Number 610973 650821 34663 34667 27793 28942 29747B 33013 650760 28545 650760 34586 33272A 650737 650738 650713 650802 34154 650713 34155 650561 650665 34186A Description Terminal Assy. (Use as required) Screw, 10-32 x 1/2" Spring, Speed control Link, Governor Clip, Conduit Screw, 10-32 x 3/8" Screw, 5/16-24 x 21/32" Cover, Starter bubble Screw, 8-32 x 3/8" Grommet, Plastic Screw, 8-32 x 3/8" Rod, Choke HMXL70-132503 Page 4 ofhead Cover, Cylinder 8 Engine Parts List #1 Screw, 1/4-20 x 1/2" (Use as required ) Screw, 1/4-20 x 5/8" (Use as required ) Screw, 5/16-18 x 5/8" (Use as require d) Screw, 1/4-20 x 5/8" (Use as required ) Plate, Upper fuel tank mounting Screw, 5/16-18 x 5/8" (Use as require d) Bracket Assy. , Lower fuel tank mtg. Screw, 1/4-20 x 5/8" Screw, 1/4-15 x 7/8" Fuel Tank (Incl. 176 & 178) NOTE: These tanks were built with different size fuel inlet openings. Fuel Cap (Red Plastic) (Spurt Resistant, Low Profile) (Use as required) Fuel Cap (White Plastic) (Std) (Use a s req. ) Fuel Cap (Ref Plastic) (Spurt Resistant, High Profile) (Use as required) Fuel Cap (Red Plastic) (Use as requir ed) Fuel Line (Use as required) (8. 25") ( 21 cm) Fuel Line (Use as required) (16. 0") ( 41 cm) Fuel Line (32. 0") (81 cm) Clamp, Fuel line (Use as required) * Gasket, Exhaust (Use as required) Muffler Plate, Muffler locking Screw, 5/16-18 x 3-3/16" Cup, Starter Screen, Starter (Stationary) Nut, Whiz lock, 1/4-28 Plug, Starter Decal, Name Inlet Needle, Seat & Clip Assy. 115) (Refer to Division 5, Section A, page 186 for breakdown) Rewind Starter (Refer to Division 5, Section C, page 30 for breakdown) * Gasket Set (Incl. [. . . ] It can be added only if cylinder hasdrilled and tapped starter mounting bosses and a ring gear flywheel has been added (see #279). Refer to service number stamped on end cap ofmotor, or decal fo Flywheel (Ring gear flywheel requiredon engine using 110-120 Volt starter motor kits listed above. ) (Use on Std. point ignition) Flywheel (Minimum ring gear flywheel required on engine using 110-120 Volt starter motor kits listed above. ) (Use on Solid State ignition) 279 610847 279 611091 [. . . ]