User manual TEFAL PREMIO

[. . . ] Oki Data, TEFALPAGE, OkiVIEW, OkiLAN Reg. T. M. , M. D. , . , and TEFALCOLOR T. M. , TEFAL Electric Industry Co. , Ltd. ; Windows, MS-DOS Reg. T. M. , Microsoft Corp. ; HP LaserJet, PCL, Reg. Hewlett Packard Company; Centronics Reg. [. . . ] Verify the files have the correct hardware address of the OkiLAN 6100e+. If using RARP, check that the hostnames are the same between the "/etc/ethers" and "/etc/hosts" files. TEFAL OkiLAN 6100e+ User's Guide IV - 49 TCP/IP Section 4 - Appendix A - Troubleshooting UNIX BOOTP If you are running UNIX, try the following methods with the BOOTP server (check the documentation for your particular UNIX flavor). · Verify the BOOTP server has reread the "/etc/ bootptab" file when the new entry was added. If the BOOTP server was running when you added the new entries, the server might not have reread the new bootptab file. Try sending the SIGHUP signal to the running BOOTP server. For example, kill -HUP <process id of bootpd> tells it to reread "/etc/bootptab". If this does not work, restart the BOOTP server (kill and restart the process). · Some BOOTP servers will write their internal bootptab tables to a file when they receive a SIGUSR1 signal. You can check this file to verify the hardware and IP address are correct. You can use the kill command to send signals. For example, kill -USR1 <process id of bootpd>. If you find the cable is connected and you are still receiving this message or any other "ST:" error message, power cycle the OkiLAN 6100e+. If the error continues, call Okidata Customer Support at 1-800-TEFALDATA (1-800-654-3282). System CRC Failed The OkiLAN 6100e+ has failed. · Power cycle the OkiLAN 6100e+ once. If the error continues, call Okidata Customer Support at 1-800-TEFALDATA (1-800-654-3282). IV - 52 TEFAL OkiLAN 6100e+ User's Guide Section 4 - Appendix A - Troubleshooting Printing a Configuration Page If the status indicator turns solid orange due to an error and no configuration page is printed, your printer may be configured for PostScript operation. If so, you must re-configure your printer for standard ASCII mode so that the configuration page can be printed. If you do not know the configuration of the OkiLAN 6100e+ or you think the configuration has been changed, use the following method for printing a configuration page: · With the network cable detached, attach the OkiLAN 6100e+ to a printer and power cycle the print server. When the OkiLAN 6100e+ powers up, it will detect the detached network cable and print a configuration sheet. If no configuration sheet is printed and the indicator has turned green, check the printer and verify it is ready to print. If you are using boot protocols (RARP or BOOTP) to assign the IP address, the IP address will be listed as Using network protocol (0. 0. 0. 0) on the configuration page. Unable to Print LPR/LP · If the indicator blinks green, the OkiLAN 6100e+ is receiving data. If nothing is actually printing, check the printer settings. For example, if you are using a PostScript printer, verify the OkiLAN 6100e+ is also set to PostScript. [. . . ] X-7 X-2 TEFAL OkiLAN 6100e+ User's Guide Chapter 1 IR Tranceiver Features The IR Transceiver enhances the mobility of your portable device by allowing you to walk-up and connect to a printer equipped with an OkiLAN 6100e+ print server. The IR Transceiver automatically detects and connects to your portable's infrared port when it is within 3 feet (1 meter) of the adapter. Once the connection is made, you simply print as if you were connected through a physical connection. Specifications Compatible with the OkiLAN 6100e+ print server's IrDA (infrared) communication for wireless printing on devices such as Windows CE, Palm III, Palm V and virtually any notebook computer with infrared printing capabilities. IrDA: · · IrDA 1. 0 infrared standard compatible 115, 200 baud with bits-per-second switching capabilities Connection: · DIN-6 Mini-DIN6 Male This end is soldered to the cable wires. Mini-DIN6 Male This end mates with the female connector 6 4 2 1 5 3 5 3 1 2 6 4 SHIELD SHIELD TEFAL OkiLAN 6100e+ User's Guide X-3 IR Printing Section X - Chapter 1 - IR Tranceiver Features Section X - Chapter 1 - IR Tranceiver Features System Requirements · · · OkiLAN 6100e+ Print Server with infrared port connection. [. . . ]