User manual TEKTRONIX DPO7UP USB3 DATASHEET

[. . . ] Automated USB 3. 0 Receiver and Transmitter Solutions TEKEXP/TEKEXPUP USB-TX/RMT · DPO/DSA70KB, DPO7UP USB3 Software Channel Emulation Models are defined for Host Channel Back Panel, Host Channel Front Panel, Cable, and Device Channel Flexible Fixture Options enable Test Access at both the Transmitter and Receiver Test Points and provide access to both USB 3. 0 Transmitter and Receiver Signals Quickly Validate Test Status with Comprehensive Reports Detailing Test Margins and Pass/Fail Results Receiver Testing Automated Receiver Compliance and Margin Testing Reduces the Complexity of Executing Receiver Tests Support for Loopback Negotiation and Custom Loopback Sequences Automated Waveform Creation for USB 3. 0 using SerialXpress Features & Benefits Transmitter Testing Provides a Comprehensive Toolset for USB 3. 0 Verification, Characterization, Debug, and Compliance Test Automated USB 3. 0 Normative and Informative Transmitter Tests ­ Single-button Execution with No User Interaction Required Full Control of Analysis Parameters enables Seamless Integration between Compliance and Debug Environments Predefined CTLE Function provided as per the USB 3. 0 Specification, DUT-specific CTLE Functions can be Customized with Serial Data Link Analysis Software (Opt. SLA) Common Configuration for Transmitter and Receiver Testing Bit Error Detection with Align Primitive Rejection for USB 3. 0 Support with the NEW Oscilloscope Error Detector Programmatic Interface Applications Transmitter and Receiver Testing USB 3. 0 Transmitter Testing for: USB 3. 0 Host and Device Silicon Validation System Validation and Integration Manufacturing Test Data Sheet View Report (Available for USB-TX, USB3, and USB-RMT) Show Schematic (Available for USB-TX and USB-RMT) Complete Automation for USB 3. 0 Testing The Tektronix TekExpress (TEKEXP) Automated Test Software is a Windows-based application that runs on any Windows XP*1 computer operating system including Tektronix Windows-based instruments. TekExpress software ordered with Option USB-TX and USB-RMT provides an automated, simple, and efficient way to test USB 3. 0 transmitter and receiver hosts and devices consistent with the requirements of the SuperSpeed Universal Serial Bus Electrical Compliance Test Specification (CTS). *1 See host system requirements in Ordering Information section. Receiver testing is a requirement for SuperSpeed USB certification. The 10x increase of data rate (5 Gb/s) makes it critical that the receiver properly interprets the incoming bit stream. [. . . ] The user also has the flexibility to change the SJ amplitude of the compliance test points. For example, a compliance test can be ran with 20% margin by easily changing the amplitude of jitter at each frequency and saving that setup. The setup can be recalled at a later point in time and the test can be run under tighter conditions. Complex SSC Profiles One source of system failures or PHY non-compliance is SSC. With USB-RMT, the user can quickly modify the SSC deviation and/or frequency modulation in order to determine if the SSC is the cause of bit errors. Furthermore, the AWG with SerialXpress can be used to generate complex df/dt profiles in order to fully characterize the receiver's pll. Stress the RX over Various Channel Configurations Using the AWG and USB-RMT enables the stressing of the receiver under various channel and cable conditions. The AWG is uniquely suited to stress the receiver by emulating the channel and USB cable in software. By using S-parameters or allowing ISI to be specified in absolute terms (for example . 3 UI) users can quickly configure a test under multiple different operating conditions without requiring physical hardware channels or USB cables. Another benefit from using software emulation is that variability from mechanical wear or different physical channels and cables is not an issue. Test Report Ellisys Protocol Analyzer Error Detection An alternative to using the scope-based error detection is to use an external USB 3. 0 protocol analyzer. The Ellisys USB Explorer 280 5 Gb/s Error Detector is completely integrated into USB-RMT and reports both 8b/10b character errors and disparity errors while ignoring SKP ordered sets. Test Status Once the test has been properly configured, USB-RMT will automatically set up and configure the test equipment. As the test points are being executed the USB-RMT will update the results dynamically. The results of the tests are shown in a tabular format and a graphical display. The graphical display supports both logarithmic and linear scales. The Test Status screenshot above shows a compliance test that has passed all of the required frequencies with the exception of 33 MHz. A supported configuration includes a DPO/DSA70000B Series Digital Serial Analyzer www. tektronix. com 5 Data Sheet (or other supported oscilloscope) equipped with DPOJET (Jitter and Eye Diagram Analysis Tools). USB-TX also includes USB3 Essentials DPOJET Measurements and Setup Library. The following table outlines the key differences between the USB3 and the USB-TX software solutions. USB3 Essentials is included with USB-TX and thus all product features included with USB3 Essentials are also included with USB-TX. Table 1 ­ Key Differences between USB3 Essentials and USB-TX Feature USB3 Essentials USB-TX Automatic measurement selections based on device type, test type, test points, and selected probes Automatic selection of Receiver CTLE filter Automatic selection of Tx Channel Modeling for Software Channel Emulation Complete coverage of USB 3. 0 Normative and Informative Tests (See Table 2) Single-button execution for all selected measurements Comprehensive debug environment allows isolation of spec violations, editing of test limits Detailed or Summary Reports Automatically save test reports and waveforms Re-analyze prerecorded waveforms USB-specific user interface Quickly move between precompliance and debug Automated Tj measurement based on Dj (CP0) and Rj (CP1) Single test report for all measurements X X X X X X Detailed Only X X X Detailed and Summary X X X X X X Required Equipment for USB 3. 0 Testing Show MOI For a complete list of required equipment please visit http://www. tek. com/Measurement/applications/serial_data/usb. html Simple Setup, Test Execution, and Reporting Setup and test execution is simple with the TekExpress software. The oscilloscope is controlled through the TekExpress automation framework. The TekExpress software provides a Graphical User Interface (GUI) and provides an intuitive workflow through setup and testing. X Setting up the Bench When setting up a test, nothing can be simpler than hooking up the test system by looking at a schematic. View the schematic of the selected test with a push of a button. Table 2 ­ Supported USB 3. 0 Transmitter Measurements Spec Reference Parameter Symbol(s) Table 6-10 Table 6-8 Table 6-12 Table 6-8 Table 6-12 Table 6-8 Table 6-12 Table 6-9 Table 6-9 Table 6-10 Table 6-10 Table 6-10 Table 6-10 Table 6-11 Table 6-11 Table 6-11 Table 6-11 Table 6-11 Unit Interval including SSC*2 Tj ­ Dual Dirac at 10­12 BER*2 Tx Deterministic Jitter ­ Dual Dirac*2 Tx Random Jitter ­ Dual Dirac*2 UI tTX--TJ-DD tTX--DJ-DD tTX--RJ-DD Instrument Bench Discovery TekExpressTM software automatically (or on demand) scans and detects supported instruments connected in your test bench (both Visa supported and non-Visa supported instruments), whether they are connected through LAN, GPIB, or USB. [. . . ] The USB key dongle will be upgraded with Opt. Includes: Latest TekExpress product software DVD kit (P/N 020-2913-xx) and upgrade SW key. Online documentation and printable manual in PDF format are supplied *3 Requires DPOJET Jitter and Eye Analysis Tools (Opt. DJA) and 8 GHz oscilloscope. Automated TekExpressTM USB 3. 0 Receiver Margin and Compliance Test Model Description DSA/DPO70000B/ MSO70000 Opt. [. . . ]