User manual TELTONIKA TVF111 BROCHURE

[. . . ] In 2003 Teltonika and NOKIA became partners and started integration of NOKIA M2M technology using NOKIA N12 module. It was the beginning of wireless technology development process. In 2004, NOKIA invited Teltonika to join presentation of M2M technology innovations in CeBIT 2004. It was very high evaluation of a small Lithuanian company and its possibilities, which helped to feel peculiarities of international business. [. . . ] 5. 2. 1. 1 Connecting phone or fax to Voice Fax Module generates the voltages necessary for the call. The phone or fax connected to the Voice Fax device can make and receive incoming calls from the GSM network. The connection to the device is shown in picture 5. 3. 2. 12 Voice Fax User Manual Picture 5. 3. 2. Phone or Fax connection to the Voice Fax 5. 2. 1. 1. 1 Call examples To make a voice or fax call, connect the phone to the Voice Fax, insert the SIM card and plug the power supply. Note: Calling mode may not work in the following situations: a) when USB cable is inserted into davice; b) when fax transmition in progress; c) when working in Service menu; d) when working with Voice Fax Configuration Tool Wait until the device gets ready for work. Enter PIN code of the SIM card if required. 5. 2. 1. 1. 1. 1 Phone call from phone to a mobile phone !Pick up the phone, connected to the Voice Fax, handset. Dial the number and wait for the connection. Time period between two different digits can be no longer than 3 seconds (see chapter 6. 1. 4. ). To terminate the call, hang up the phone. Note: Making international phone call dial 00, instead of + 13 Voice Fax User Manual Picture 5. 3. 3. Phone call from phone to mobile phone 5. 2. 1. 1. 1. 2 Phone call from mobile phone to phone Dial the number of the SIM card inserted in the Voice Fax and wait for the signal. Picture 5. 3. 4. If *** will be pressed at the moment when device is connecting, sending, calling will be terminated and data deleted from flash after unsuccessful attemp will be finished. ! ! ! ! ! ! ! 16 Voice Fax User Manual 5. 3 Connecting Voice Fax to the PC The connection of Voice Fax device is performed in the following order: !Connect one mini USB cable end to the device and the other to the USB port in the PC (picture 5. 4. 1). If the device is being connected for the first time, mini USB cable must be connected during the drivers installation. Connect AC/DC power supply source to the supply socket of the device (picture 5. 5. 1). ! Picture 5. 4. 1. Connection to the PC 17 Voice Fax User Manual 5. 4 Connection of the power supply Voice Fax module uses 9V 1. 12 A direct current power supply source which goes with the package. The connection of the power supply is shown in picture 5. 5. 1 . Picture 5. 5. 1. Connection of the power supply 18 Voice Fax User Manual 5. 5 THE START When the Voice Fax device is set to work, that is, SIM card inserted, antenna, phone, analog phone line or PC (depending on needs) and power supply are connected, the Power LED is on and the Status LED is blinking indicating, that the module is preparing for work. The initialization can take up to 20 seconds (it is recommended to wait). During that time, the module checks the SIM card, detects the appropriate GSM network and checks the operating parameters. When initialization is done, the Status LED becomes constant. After power on, when USB cable is pluged in, only when status LED becomes constant, Voice Fax will enter USB mode. [. . . ] Dial 13# in the main menu in order to get to Set delay between tries menu. 0# 27 Voice Fax User Manual To set time interval between tries ##1111# 13# (1. . . 60)# 0# 6. 14 Turning on/off allways answer as fax There is a possibility to activate allways answer as fax function. If it is on, device automaticaly will answer as a fax machine after defined number of rings even if incomming voice call. Dial 14# in Service menu in order to get to Turning on/off allways answer as fax menu. [. . . ]