User manual TEXECOM PREMIER 24

[. . . ] To PART arm the system, press !, ( or " followed by ). Keypad Lock The keys on the keypad can be locked to prevent unwanted access to the system. To Lock the keys, press * and + together. To Unlock the keys, press * and + together again. 2 INS221 !" The Emergency keys will NOT operate with the keys locked. Premier Series User Guide Overview LED Indicators Five LED indicators have been provided to indicate the status of the system. LED Power Status On Flashing Meaning AC mains is present on the control panel AC Mains is not present, the control panel is running on the standby battery The system requires attention, contact your installer The system does NOT require attention All zones are secure and the system is ready to be armed One or more zones are active The system has zones (with the `Force Omit' attribute) that are active The system is armed (can also be programmed for other indications) The system is unarmed (can also be programmed for other indications) One or more zones are omitted No zones are omitted Service On Off Ready On Off Flashing Info. On Off Omit On Off Zone Faults During Arming Before attempting to arm the system, ensure that the premises are secure (all doors and windows closed etc. ) and the Ready light is on. [. . . ] Leave the protected area When the system has armed, the exit tone (if sounding) will stop 4 INS221 Premier Series User Guide Operating the Alarm System To ARM Individual Areas If the system has been split up into separate areas of protection i. e. Area 1 = House, Area 2 = Garage, Area 3 = Shed etc. These areas can be individually selected for FULL or PART arming as required. !" Areas are selected by using keys !(the select an area followed by ' or +). / key can also be used to Only areas that exist on the system can be selected. (A `Star' means the area can be selected and a `Dot' means the area cannot be selected). Pressing 0 will select/deselect all areas, pressing ' will toggle between the first 8 areas and the second 8 areas (where applicable). Ensure that the premises are secure (all windows and doors not being omitted are closed) and the Ready light is on 2. Press * or - to FULL arm the areas Or 5. Press )!, ( or " followed by * or - to PART arm the areas The exit tone will sound (if silent arm has not been selected) 6. Leave the premises When the system has armed, the exit tone (if sounding) will stop To DISARM the System The entry time is divided into two sections, the Entry time and the 2nd Entry time. If the Entry time expires, an Internal alarm will occur and the 2nd Entry time will start. If the 2nd Entry time expires, an Intruder alarm will occur (all internal and external sounders). !" It is perfectly normal for the 2nd Entry time to be programmed as zero, in which case, an Intruder alarm will occur as soon as the Entry time expires. 1. Enter the premises via the designated entry point The entry tone will start 2. Enter a valid User code , , , , The entry tone will stop INS221 5 Operating the Alarm System Premier Series User Guide To DISARM the System When Not in Entry 1. Press * To CANCEL the Exit Mode Once the exit mode has been started you should leave the premises immediately, however, if for some reason you decide not to leave, the exit mode must be cancelled. Press * The exit tone will stop. To CLEAR an Arm Fail When the system tries to arm with zones active (open), the internal sounders will sound and the external strobe will be flashing to indicate a problem. For details on preventing an Arm Fail condition, please refer to page 3. !" If you were not present when the Arm Fail occurred or you do not clear the Arm Fail, the internal sounders will continue to sound and the external strobe will continue to flash. 1. Enter a valid User code , , , , The internal and external sounders will stop, the external strobe will continue to flash and the number of the zone that caused the Arm Fail will be displayed. Enter a valid User code , , , , and press 12 To SILENCE an Alarm When an alarm occurs on the system, the internal and external sounders will normally sound for a pre-programmed time (normally 15 minutes). !" If you were not present when the alarm activated, the internal and external sounders may have already stopped but the external strobe will still be flashing. When alarm information is being displayed, pressing the SCROLL key will slow down the display and also allow manual scrolling through the events. 1. Enter a valid User code , , , , The internal and external sounders will stop and the number of the zone that caused the alarm will be displayed. 6 INS221 Premier Series User Guide Operating the Alarm System To RESET After an Alarm USER Reset Once the alarm has been silenced (see page 6 for details), the system will need to be reset. !" If the system has been programmed, to be reset by an Engineer, pressing 1 will not return the display to normal, if this is the case see ENGINEER Reset for details. The system may have been programmed to be reset by Anti-code, if this is the case, see ANTI-CODE Reset for details. [. . . ] Press 4 when finished Continue to arm the system as normal. The Turn CHIME On and Off The system can be set up so that activating (opening) certain zones will cause the internal sounders to chime. This would normally be used on a front door, exit button etc. !" !" Zones will only cause the internal sounders to chime if they are selected for chime (see page Master User Guide for details on selecting which zones chime). Once a zone has been selected for chime, the Chime facility can be manually turned on and off as required. The system can also be programmed to automatically turn chime on and off under certain conditions i. e. certain times of the day, door left open etc. [. . . ]