Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual THEBEN QUICKFIX. We hope that this THEBEN QUICKFIX user guide will be useful to you.
Lastmanuals help download the user guide THEBEN QUICKFIX.
Manual abstract: user guide THEBEN QUICKFIXFICHE TECHNIQUE
Detailed instructions for use are in the User's Guide.
[. . . ] ⷠUnique lens pattern - Distribute total 304 zones "no dead spot" in its 360° high intensity detection, such as a small waving movement can be detected. Quick connector - RJ11 Connector easy for plug in connection. The LU 361 PE2 LU 361 PE LU 361 PE-S can be mounted on the ceiling and widely used in offices, conference rooms, hotels, utility rooms, kitchens and lavatories. While mounting on locations above mentioned, it is highly recommended to install at height of 2. [. . . ] Avoid directing the sensor toward areas or objects whose surfaces are highly reflective or are subject to rapid temperature change, such as pools. Do not aim the sensor toward light devices. Switch off power supply before installation. Please read the instruction manual carefully before installation 2. Be sure all power supply is switched off. To install the sensor, please drill a hole (diameter of 65 mm) on the ceiling and keep the power cable above ceiling board (SeeFig. When installing LU 361 PE2 and LU 361 PE-S on the same ceiling, assure the two holes is max. 3M away and the thickness of ceiling board is 5-25 mm (See Fig. Both LU 361 PE2 and LU 361 PE-S sensor can be connected to one power box at the same time. To install the second sensor (LU 361 PE-S), please keep the signal cable to pass through the hole (SeeFig. Walk from outside across to the detection zone (See Fig. Once the sensor is triggered, the light will turn on for 5 secs. Repeat step 3 to 5 until you are satisfied with the detection coverage. Slightly pull out sensor head with a screwdriver before knobs adjustment (See Fig. LUX, METER, TIME knob Adjust LUX, TIME, METER knobs according to the desired value marked beside each knob (See Fig. Time and LUX knobs must be set at value figure marked. DO NOT adjust knobs in between of two value figure marked to cause value functional failure or value confusion. In this mode light is uncontrolled by LUX. Short impulse mode: Time 1/Time knob setting to "impulse", the sensor automatically enters into short impulse mode. * Set METER knob to "1m", the sensor will operate within very limited small "field of view" with a diameter of approx. [. . . ] Short impulse mode: Time 1/Time knob setting to "impulse", the sensor automatically enters into short impulse mode. * Set METER knob to "1m", the sensor will operate within very limited small "field of view" with a diameter of approx. When sensor fails to work normally, check assumptive problems and suggested solutions in following table that will be hopeful to solve your Power does not switch on. Please check whether the power supply and load are connected correctly. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE THEBEN QUICKFIX
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual THEBEN QUICKFIX will begin.
