User manual THERMA MW2401-M

[. . . ] Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the appliance. Installation q Check your dishwasher for any transport damage. If your dishwasher is damaged, you should contact your supplier. [. . . ] In this case the rinse aid inflow must be deactivated in order to avoid a double dosage. Filling with rinse aid 1. Open the container by pressing the release button (A). Add the rinse aid until the container is completely full. The maximum level for filling is indicated by "max". Deactivation/activation of the inflow of rinse aid (The dishwasher must be switched off) Factory setting: inflow of rinse aid activated When the inflow of rinse aid has been deactivated, also the rinse aid indicator light on the control panel is automatically deactivated. All programme selection push buttons indicator lights will illuminate (setting mode). If only one programme selection push button indicator light is illuminated, this means that a washing programme has been selected. The programme must be cancelled: press simultaneously the function push buttons 2 and 3 for about 2 seconds, the indicator light of the setted programme push button starts flashing for about 2 seconds. After about 2 seconds the indicator lights of all the programme selection push buttons will illuminate indicating that the setted programme has been cancelled and that the machine is now in setting mode. Press simultaneously function push buttons 2 and 3, the indicator lights of the function push buttons 1, 2 and 3 start flashing. Press the function push button 2, the indicator lights of function push buttons 1 and 3 turn off while the indicator light of the push button 2 goes on flashing, at the same time the end of cycle indicator light illuminates, indicating that the inflow of rinse aid is active. To deactivate the inflow of rinse aid, press again the function push button 2, the end of cycle indicator light turns off, indicating that the inflow of rinse aid has been deactivated. Serving dishes and large lids should be arranged around the edge of the basket, ensuring that the spray arms can turn freely. UI92 UI51 UI12 32 The cutlery basket Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their handles facing upwards. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Mix spoons with other cutlery to prevent them from sticking together. To unload your dishwasher more easily, you can take the cutlery basket out of the lower basket and unfold it. This makes it easier to remove small pieces of cutlery. To prevent the full cutlery basket from inadvertently unfolding when being taken out, place your hand right round the two-piece handle and hold it firmly. Place the cutlery basket on a firm support (table, worktop) and unfold both handle parts. After unfolding, fold back both handle parts. Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in upper basket lower basket With upper basket raised With upper basket lowered 20 cm 24 cm 31 cm 27 cm To move to the higher position proceed as follows: 1. [. . . ] Check the water inlet hose connection. Clean out the siphon. The water drain hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. Protection against flooding is active. Close the water tap and contact your local Service Force Centre. Once the checks have been carried out, to continue the programme press the push button of the programme that was running before the intervention of the alarm and close the door. The programme will continue from the point in which it was interrupted. If the fault code reappears contact your local Service Force Centre. For other combinations of fault codes not described in the above chart will appear, please contact your local Service Force Centre. . . . there are problems when operating the dishwasher Fault Possible cause The dishwasher door has not been properly closed. [. . . ]