User manual THERMADOR 14-33-873F

[. . . ] I UL LISTED #157J FILE # E521958 INSTALLATION INSTRUCTIONS MANUAL 30" BUILT-IN RANGES WITH COOK'N'VENT ELECTRIC MODEL RED30V DUAL-FUEL MODEL RDDS30V PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: INSTALLER: OWNER: WARNING: Save these instructions for the local electrical inspector's use. Please leave these Installation Instructions with this unit for the owner. Please retain these instructions for future reference. Before installing turn power OFF at the service panel. [. . . ] Do not replace top until installation is complete. Provide a square hole through the roof (or wall), as shown by dashed lines, or cut a round hole to fit duct with a separate hole for electrical conduit as shown by solid lines in Figure 10. See Figure 12 for remote blowers dimensions. Install the Remote Blower on the roof or wall (with discharge pointing down slope) according to the Standard Roofing Procedures (front discharge edge should be on the top of shingles and the rear edge underneath the shingles). Connect blower to the exhaust system with 8 inch dia. Use adjustable elbow to adjust to roof angle. Figure 10 - Remote Blower Cutouts 9" dia. VTR600R 10" dia VTR1000Q 14" 6-1/8" 1" 1" 4-11/16" for VTR600R 6-1/4" for VTR1000Q 1-1/4" Hole 14" Figure 11 ­ Curb for roof 20-3/4" 28" Figure 12 Remote "J" Box Blower Dimensions A Adjustable Elbow 9-3/8" C 11-3/8" 5-7/8" G D E F 20-3/4" 28" H Conduit (Not Provided) Tape Joints B Dia. Duct Conduit J MODEL A B C VTR1000Q 10" Dia. 10-3/8 D 10-1/4 11-1/4 E 3-3/16 4-5/8 F 17-5/8 14-1/2 G 10-3/4 8-3/4 H 10 8 I 26-1/4 24 NOTE: The unit must be sealed between the roof (or wall) and the underside of the flange with roofing mastic to prevent leaks. For installation on a flat roof, or roofs with a pitch less than 1-1/2" in 12", install ventilator on the curb as shown in Figure 11. Position the curb on flat roofs so that the discharge (low) end points away from prevailing wind. 8 I J 4 3-1/2 2" 5-1/2" INSTALLING THE VENTILATION I 4. The duct put into the unit inlet blower should be taped at the joint and the inlet collar. Clearance to combustible material is 0". Figure 13 SAFETY WARNING: Before wiring the unit, turn off the proper circuit at the service box. 6. Run electrical conduit up through extruded hole in bottom of the remote blower. Connect it to the bottom of the "J" box (Fig. 13). 7. Run five #14 AWS wires (white, red, blue, black and green) to the conduit, (Fig. 13). For the wire connection between the remote blower and range see page 7 and Figs. 8 & 9. VENTILATION I The range is equipped with a factory installed ventilator intake and an exhaust plenum which will not be shipped separately. The plenum exhaust outlet is located below the oven in the base area shown in Fig. 14. An Integral Blower Model VTN30Q or Remote Model VTR1000Q Blower System must be installed with the range. [. . . ] Fitting (Dia. ) 6" 7" 8" = = = = Straight Length 10 Ft. Fitting (Dia. ) 6" 7" 8" = = = = Straight Length 2 Ft. 45° Elbow 3-1/4 " x 10" to 10" Dia. 10" Dia. 3-1/4" 6" I ANTI-TIP BRACKET INSTALLATION INSTALL ANTI-TIP BRACKET Two anti-tip brackets are supplied. [. . . ]