User manual THERMADOR 209902480

[. . . ] PROPANE GAS INSTALLATION The propane gas tank must be equipped with its own high pressure regulator in addition to the pressure regulator supplied with this unit. The cooktop is shipped from the factory for use with natural gas. For use with LP conversion kit ­ Model SNLPKIT6, must be purchased separately. A qualified technician or installer must do the conversion. [. . . ] Clearance From Cooktop to Start of Radius 4-1/8" Min. to Right Side Wall A B C 1- /8" Min. to Counter Front 7 D 7-1/8" Min. to Left Side Wall Cooktop A Cut-out B Cut-out C Corner 30" Models 19-1/8" to 19-7/8" 36" Models 19-1/8 to 19-7/8" 45" Models 19-1/8 to 19-7/8" 28-15/16" to 29-3/8" 30" 34-15/16" to 35-3/8" 36" 43-15/16" to 44-1/2 45" Cutout Dimensions are Underlined D Overall 31" 37" 46" PAGE 2 Page 1 of 4 Revision 10/16/01 SGS/X 45" Cut-Out SGS 45" Cut out SGCS 45" Cut-Out 43 15/16 - 44 1/2 43 5/8 - 44 1/2 19 1/8 - 19 7/8 19 1/8 - 19 7/8 1114. 3mm 475. 6mm Rough-in R/I Tol 18. 71 in 0. 015 in 475. 25 mm 0. 381 mm R/I R/I Tol 2 Screw Washer 18. 725 in 475. 631 mm 43. 585 0. 015 0. 118 0. 034 43. 87 in in in in in 1107. 05 0. 381 2. 9972 0. 8636 1114. 289 mm mm mm mm mm Page 2 of 4 Revision 10/16/01 SGS/X 36" Cut-Out SGS 36" Cut out SGCS 36" Cut-Out 34 15/16 - 35 3/8 34 5/8 - 35 3/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 886. 7 mm 475. 6mm Rough-in R/I Tol 18. 711 in 0. 015 in 475. 25 mm 0. 381 mm R/I R/I Tol 2 Screw Washer 18. 726 in 475. 631 mm 34. 623 0. 015 0. 118 0. 034 34. 908 in in in in in 879. 43 0. 381 2. 9972 0. 8636 886. 669 mm mm mm mm mm Page 3 of 4 Revision 10/16/01 SGS/X 30" Cut-Out SGS 30" Cut out SGCS 30" Cut-Out 28 15/16 - 29 3/8 28 5/8 - 29 3/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 733. 1 mm 478. 1mm Rough-in R/I Tol 18. 809 in 0. 015 in 477. 75 mm 0. 381 mm R/I R/I Tol 2 Screw Washer 18. 824 in 478. 131 mm 28. 58 0. 015 0. 118 0. 034 28. 865 in in in in in 725. 9 0. 381 2. 9972 0. 8636 733. 139 mm mm mm mm mm Page 4 of 4 ND SGS 45" Cut out SGS 36" Cut out SGS 30" Cut out With Cook and Vent CW CD OW OD SB BT ND Cutout Width Cutout Depth Overall Width Overall Depth Set Back Backsplash Notch Depth 43 15/16 22 1/8 46 23 5/8 1 1/2 1 1/4 3 34 15/16 22 1/8 37 23 5/8 1 1/2 1 1/4 3 28 15/16 22 1/8 31 23 5/8 1 1/2 1 1/4 3 SGS 45" Cut out SGS 36" Cut out SGS 30" Cut out Without Cook and Vent 43 15/16 - 44 1/2 19 1/8 - 19 7/8 34 15/16 - 35 3/8 19 1/8 - 19 7/8 28 15/16 - 29 3/8 19 1/8 - 19 7/8 SGCS 45" Cut-Out SGCS 36" Cut-Out SGCS 30" Cut-Out 43 5/8 - 44 1/2 34 5/8 - 35 3/8 28 5/8 - 29 3/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 19 1/8 - 19 7/8 CVS30 CVS36 CVS45 28 5/8 34 5/8 43 5/8 INSTALLING THE COOKTOP 1. Seal the Cooktop Apply the foam tape packaged with the cooktop to underside of the cooktop along the perimeter before installing. Important: For solid surface material installations such as Sure l TM ® and Corian , consult with solid surface manufacturer. Apply heat reflective tape such as Scotch® Aluminum Foil Tape #425 or #427 around the cutout so that it folds over on the top and sides. DO NOT WRAP THE TAPE UNDERNEATH THE COOKTOP. Be sure the tape extends beyond the outermost flange of the cooktop. All corners should be covered with tape. Attach Brackets to the Cooktop Attach clamps of the hold-down brackets packaged with the cooktop to the rough-in box. Install the Cooktop Insert cooktop into the cutout. Adjust hold-down brackets to desired position and tighten screws to rough-in box. Insert adjusting screw into clamp and secure cooktop to countertop. Important: For solid sur face material installations: Insert a wooden block between the end of the screw and the bottom of the countertop. Trim excess aluminum tape around cooktop flange. Connect Gas Supply The gas inlet to the unit is located at the right rear of rough-in box. After installing a gas shut-off valve in an easily accessible location under the unit (see Figure 6), install the pressure regulator (supplied) to manifold pipe using Teflon® tape on threads of manifold pipe. To prevent possible damage to the gas pressure regulator, install it after the rough-in box is in its permanent position. CAUTION: Do not attempt any adjustment of the pressure regulator, except conversion to propane. [. . . ] Install Knobs Install control knobs by placing indicator line at 12 o'clock position; press down firmly. 30" Models Only Two center control knobs have a silver ring on the shaft. Final Check After electrical connection is complete, place each burner cap in correct sized notched position and check operation of electric igniters. Flame should be blue with no yellow tip. For technical service questions contact Customer Relations at 1 (800) 735-4328. [. . . ]