User manual THERMADOR 5060004396

[. . . ] When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. WARNING b) Always turn the hood ON when cooking at high heat or when flambéing foods. Grease should not be allowed to accumulate on fan or filter. Always use cookware appropriate for the size of the surface element. G. Ducted fans must always be vented to the outdoors and upward. [. . . ] for 60" hood Grease Troughs ­ (4 pieces) Wire Nuts Halogen Bulbs - 4 bulbs (20 Watts ea. ) To be purchased separately: Remote Ventilator Models: choose one of these units VTR1000Q - 1000 CFM, 3 speed, remote ventilator VTR1400Q - 1400 CFM, 3 speed, remote ventilator Duct Tape 2" wide Lug Screws - 1/4" Diameter x 5" Long (qty. 8) Lug Bolts - 1/4" Dia. 8) & taps (qty. 8) Angle Brackets - 2" x 2" x 1-1/2" (qty. 4) 2" Dry Wall Screws (qty. 24) Bolts - 1/2" Diameter x 5" (qty. 16) Adjustable chimney mounting structures may be purchased separately in the following sizes: Pro Island Chimney Assembly 9 to 15" PHICHIM15 Pro Island Chimney Assembly 15 to 27" PHICHIM27 Pro Island Chimney Assembly 27 to 51" PHICHIM51 PAGE 3 TYPICAL INSTALLATION The Professional Island hood is designed to be installed on a rigid structural framing. Follow these installation steps for proper hood performance. Typical installation of the Island Hood is shown in Figure 1. 10" Transition To Be Connected to Remote Ventilator 12" min. NOTE: BECAUSE OF THE SIZE AND WEIGHT OF THE ISLAND HOOD, IT IS NECESSARY TO MAKE A 12" WIDE BY HOOD LENGTH SOFFIT WITH RIGID STRUCTURAL FRAMING IN AN 8-FOOT HIGH KITCHEN CEILING. Filters 15" Lights 30" to 36" Adjustable chimney structures are available. Fig. 1 STEP 1 SOFFIT FRAMING a) Locate and mark the center line of the hood location. b ) Use 2 pieces of 2" x 6" x 6 feet wood spacers and bolt these pieces onto the ceiling joist as shown in Fig. If the ceiling joists are spaced more than 16" apart center to center, it is necessary to install additional spacers so that when installing the vertical studs, they will be 11" apart. c) Using 1/4" diameter x 5" long lug screws, attach 2" x 6" vertical studs onto the spacers so that their inner edges are 23" apart. 2 The length of these studs depends on the ceiling height and the desired height of the hood from the top of the cooktop. The bottom of the hood is recommended to be within 30" to 36" over the range cooking surface. 2 23" 48" Hood - 46 3/4" 60" Hood - 58 3/4" Vertical Studs Spacer 16" Bolts Vertical Studs 11" 2" x 6" Spacers Existing Ceiling Joists Fig. 3 PAGE 4 d ) Construct the bottom wood framing with 2" x 4"s as shown in Fig. The center of the frame must have an opening of 10" x 23" for the transition duct. e ) The overall length of the structural framing will depend on the size of the island hood. Attach 2" x 4" wood frame onto the ends of 2" x 6" so that their outer edges are 47" apart for 48" hood, or 59" apart for a 60" hood. See Figure 2. NOTE: Because of the weight of the hood, we are recommending that you use metal joint straps to connect the ends of wood framing per example of Figure 4. f ) Using 2" x 6" wood, construct the bottom framing for duct opening at the center bottom of the soffit. The duct opening must be 8" x 23" as shown in Fig. 7. See Detail "A" 2" x 4" Frame Detail "A" Fig. 4 STEP 2 INSTALL HOOD ASSEMBLY a ) Install the transition (provided) to the top of the hood using #8 x 1/2" Philips head screws. b ) Locate and mark the centerlines of the hood soffit framing and hood assembly. [. . . ] Use the provided wire nuts to connect the black, white, and green wires to the corresponding color wires located inside the J-box. (Note: follow the wiring diagram. ) c) When using the power supply in a damp location or outdoors, always install it in a GFCI protected branch circuit. Fig. 7 STEP 5 INSTALL GREASE TROUGHS AND FILTERS See Care and Use for instructions. PAGE 6 STEP 6 TURN THE POWER ON AND CHECK HOOD OPERATION Fig. 11 STEP 7 INSTALL DRYWALL ON THE SOFFIT ADJUSTABLE CHIMNEY MOUNTING STRUCTURES MAY BE PURCHASED SEPARATELY IN THE FOLLOWING SIZES: Pro Island Chimney Assembly 9 to 15" PHICHIM15 Pro Island Chimney Assembly 15 to 27" PHICHIM27 Pro Island Chimney Assembly 27 to 51" PHICHIM51 Chimney Fig. 12 PAGE 7 We reserve the right to change specifications or design without notice. [. . . ]