User manual THERMADOR 9000001005

[. . . ] TM Dishwasher Installation Manual For Models DW44ZB, DW44ZW, DW44ZS, DW44ZP, DW44FI ENENENENENGLISH GLISH GLISH GLISH GLISH TM Installation Instructions Table of Contents IMPORTANT INSTRUCTIONS . . . . . . . . . . . . . . . . Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Materials Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Materials Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Remove 3" - 4" (75mm - 100mm) of the cable's outer casing, as shown in Figure 6, letter C, then remove 3/8" - 1/2" (9 - 13mm) of insulation from each conductor, as shown in Figure 6, letter D. Dishwasher Electrical Rating ENENENENENGLISH GLISH GLISH GLISH GLISH B 30" (762mm) A 21" (533mm) Figure 5/Ilus. 6 Volts 120 Hertz 60 Amperes 15 Watts 1, 450 (max) 5 Electrical Preparation PLUMBING PREPARATION WARNING: SCALD HAZARD Serious injury could result if work is performed on a charged hot water line. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off. CAUTION: Temperatures required for soldering and sweating will damage the dishwasher's base and water inlet valve. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152. 4 mm) away from the dishwasher's base and water inlet valve. Hot Water Supply Thermador recommends that the hot water heater be set to deliver approximately 120° F (49° C) water to the dishwasher. Water that is too hot can cause some detergents to loose effectiveness. Lower water temperatures will increase run time. The hot water supply pressure must be between 5 - 120 psi (0. 3 - 8. 27 bars). Hot Water Supply Plumbing NOTE: Regardless of where the hot water supply line enters the enclosure (following the guidelines on page 8), position the line 14" (355mm) from the enclosure's left side, as shown in Figure 7, letter A. NOTE: Decide whether braided hose or copper tubing will be used for the hot water supply plumbing, and purchase the correct type of hot water supply shut-off valve, 90° elbow, and necessary fittings for the hot water supply plumbing. Install an easily accessible shut-off valve (not supplied) in the hot water supply line, as shown in Figure 7, letter B. All solder connections must be made before the water line is connected to the dishwasher's water inlet valve. Water may also be supplied to the dishwasher by using a braided hose line. Check with your local plumbing supply sources for the proper hose and 90° elbow fitting. (Continued on next page) Plumbing Preparation 6 B 14" (355mm) A Figure 7 PLUMBING PREPARATION (continued) Drain Plumbing Dishwasher Connection Piece If the dishwasher is to drain either directly into the household drain plumbing or through an air gap, install a dishwasher connection piece under the sink, as shown in Figure 8, letter A. Installing an Air Gap If local ordinances require an air gap, as shown in Figure 9, letter B, install it according to the manufacturer's instructions. Disposer If a disposer is to be installed, as shown in Figure 10, letter C, install it according to the manufacturer's instructions. Whether the disposer is newly installed or existing, remove the disposer's dishwasher drain connection plug. B A Figure 8 ENENENENENGLISH GLISH GLISH GLISH GLISH Figure 9 DISHWASHER PREPARATION Dishwasher preparation involves four tasks: · Installing the Mounting Brackets · Removing the Toe Panel · Installing the 90° elbow fitting · Junction Box Preparation Installing the Mounting Brackets CAUTION: Before installing the supplied mounting brackets (letter E in the Materials Supplied section of this manual), decide which method of securing the dishwasher into its enclosure will be used. Once the mounting brackets are installed on the dishwasher, removing them is difficult and will damage the mounting brackets and the dishwasher. [. . . ] MAKE CERTAIN THAT ALL ELECTRICAL CONNECTIONS ARE PROPERLY MADE. · Do not pre-twist the wires before connecting them with wire nuts. · Extend the dishwasher's stranded wires 1/8" (3mm) beyond the power supply cable's solid wires, as shown in Figure 22. 5) Using the supplied wire nuts, connect the electrical supply wires to the dishwasher's wires, black to black, white to white, and green or bare to green or bare. [. . . ]