User manual THOMSON 10MG10U

[. . . ] Replace the batteries when the unit no longer operates at normal viewing distances. When replacing batteries do not mix old and new - do not mix makes and types. alkaline types are recommended for long life. Never risk damage to the remote control by extreme heat - do not leave close to a radiator or on a window ledge in direct sunshine. 1 Connections 220 - 240V ~ 50Hz 2 1. [. . . ] button on the remote control three AUTO INSTALL. UK A new menu appears. The cursor moves from left to right on the VL line, then on the VH line and then on the U line. The channels found are stored in memory in order starting from programme PR 01. AUTO INSTALL. UK VL You can stop the automatic search at any time by pressing PR01 the button. The search stops automatically at the end of the U band or when 99 channels have been found. The Programme Organizer menu then appears automatically. The channel stored on programme PR 01 is selected (see next page). 5 Changing a Programme Number Select the channel number to be changed using the button. AUTO INSTALL. Using the numerical keypad on the remote control, enter the new programme number. You can also use the Press the buttons on the remote control. UK VL PR01 button to confirm the change. The programmes stored under the old and new numbers are then swapped. Repeat this operation to change other programme numbers. Erasing a Programme Select the programme to be erased using the button. Enter 0 or 00 on the numerical keypad of the remote control. button, then press Check that all the programmes are in the required order using the to leave the menu. 6 Manual Channel Setting Press the button twice to call up the channel setting menu. 1. Channel Search Select the 2nd line of the menu using the Start the search by pressing: ­ the ­ the button for a forward search, button for a backward search. UK VL PR button. The search fully covers the VL, VH and U bands starting from the channel on the screen. The cursor moves and as soon as a channel is found, the picture appears on the screen. Wait for the menu to go to the bottom of the screen for optimum reception. If the picture corresponds to the channel required, go to the 4th line (PR), otherwise continue the search. If you wish to stop the automatic search, press the button. 2. Programme Number and Storing in Memory Select the 4th line of the menu using the button. UK VL PR If fine tuning is necessary, see Fine Tuning Enter a programme number using the numerical buttons of the remote control. You can also use the buttons. button. Store the programme number you have allocated to the channel by pressing the The 2nd line of the menu is then selected again. Restart the search using the buttons. 7 3. Fine Tuning Only necessary in the event of interference If fine tuning is necessary, select the 3rd line of the menu using the button. buttons. PR UK VL If necessary, adjust the picture using the Select the 4th line (PR) using the button to allocate a programme number to the channel and store it in memory (see Programme Number and Storing in Memory) If a channel has required fine tuning, it will be stored in memory with the AFC (Automatic Frequency Control) deactivated. Press the button to leave the menu. 8 Picture Adjustments Press the button to call up the Picture Menu. = BRIGHTNESS = COLOUR = CONTRAST = SHARPNESS = TINT Select the function to be adjusted using the The tint function is only active in NTSC mode. Adjust as required using the buttons. buttons. Storing Personal Adjustments You can store the adjustments you have just made and call them up at a later stage. Caution: these personal adjustments will replace and delete the standard settings made at the factory. With the Picture Menu displayed, press the red Press the button to leave the menu. button. Sleep Timer Press the green Menu. Set the stand­by time in 10­minute steps (up to 4 hours) using the Press the buttons button to leave the menu : button to call up the Stand­by The television set is child locked when the programmed time period has elapsed. The stand­by indicator will flash (see Day to Day Operation). [. . . ] Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer's instructions. Switch off and withdraw the mains plug when making or changing connections. Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. Don't continue to operate the equipment if you are in any doubt about it working normally or if it is damaged in any way-switch off, withdraw the mains plug and consult your dealer. Don't use makeshift stands and NEVER fix legs with wood screws-to ensure complete safety always fit the manufacturer's approved stand or legs, with the fixings provided, according to the instructions. [. . . ]