User manual THOMSON 14MG10G

[. . . ] Even if the ON/OFF switch is in the OFF position, the set is not completely disconnected from the mains. To disconnect the set completely, pull out the mains plug. GB DO NOT OBSTRUCT VENTILATION OPENINGS. AVOID WATER, HEAT, DIRECT SUNLIGHT. Do not place audio loudspeakers next to your TV set as the magnets in the speakers may cause coloured patches on the screen. Remove the mains plug from the wall outlet in the following cases: 1. It is wise to disconnect the aerial plug too in this case. If you notice any odour or smoke coming from your set. [. . . ] S-VIDEO is then displayed at the bottom button. GB When you switch off the device and if you have not changed channel during play, the TV set automatically returns to the previous channel. If the TV set has been switched on by the video recorder, it will be placed on stand­by when the video recorder is switched off. 3 Remote Control Display programme No. and sleep timer (Yellow button) Stand-by Display Timer Menu (Green button) Inactive GB Inactive Call up personal adjustments (Red button) Confirm an action or validate a menu option To leave a menu Adjustment: move to Right/Left in menus and select one of the proposed options To go to Picture and Channel Adjustment menus Move Up and Down in the menus Volume level To change programme Sound mute To switch to connected equipment (e. g. : video recorder) 8 Direct access to programmes and entering numerical values in menus Batteries: Remove the lid at the back of the remote control and insert two 1. 5 V, LR06 batteries. Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling. . " 4 Automatic Channel Setting This set is equipped with an automatic search system which will search for and store all channels available in your region. To help identify the programmes, we suggest that you have to hand a TV guide or daily newspaper. Ensure that the aerial lead is connected to the TV set. Check that any equipment connected only via the aerial (video recorder or satellite equipment) is operating. Switch off any equipment connected via the SCART socket. GB Installation Press the ON/OFF button, the indicator lamp lights up. If the television set remains on stand­by, press one of the buttons on the remote control numerical keypad. When the television set is turned on for the first time, the Installation menu appears automatically. If this is not the case, you can call it up by: ­ pressing the times. button on the remote control three AUTO INSTALL. EURO A new menu appears. The cursor moves from left to right on the VL line, then on the VH line and then on the U line. The channels found are stored in memory in order starting from programme PR 01. AUTO INSTALL. EURO VL You can stop the automatic search at any time by pressing PR01 the button. The search stops automatically at the end of the U band or when 99 channels have been found. The Programme Organizer menu then appears automatically. The channel stored on programme PR 01 is selected (see next page). 5 Changing a Programme Number Select the channel number to be changed using the button. AUTO INSTALL. Using the numerical keypad on the remote control, enter the new programme number. GB You can also use the Press the buttons on the remote control. EURO VL PR01 button to confirm the change. The programmes stored under the old and new numbers are then swapped. Repeat this operation to change other programme numbers. Erasing a Programme Select the programme to be erased using the button. Enter 0 or 00 on the numerical keypad of the remote control. button, then press Check that all the programmes are in the required order using the to leave the menu. 6 Manual Channel Setting Press the button twice to call up the channel setting menu. 1. Channel Search Select the 2nd line of the menu using the Start the search by pressing: ­ the ­ the button for a forward search, button for a backward search. EURO VL PR button. GB The search fully covers the VL, VH and U bands starting from the channel on the screen. The cursor moves and as soon as a channel is found, the picture appears on the screen. Wait for the menu to go to the bottom of the screen for optimum reception. [. . . ] If the channel has been fine tuned, the This information disappears automatically after a few seconds. Press the yellow again to delete this information. button Stand-by - Sleep Timer Press the button to switch the television set to stand­by mode. The television set will automatically switch to Stand­by after a few minutes if there is no signal on the channel being watched. Child Lock You can prevent the use of your television set using the keypad. [. . . ]