User manual THOMSON DPL560

[. . . ] DPL560-EN 4/11/02 5:27 PM Page 2 EAT HOME TH ON/ECO SOURCE MUTE AL DIGIT SOURCE PHONES Thomson multimedia 46/47 quai A. Le Gallo 92648 Boulogne Cedex FRANCE RCS nanterre B322 019 464 55199360 www. thomson-multimedia. com DPL560-EN 4/11/02 5:27 PM Page 3 u s e r m a n u VOLUME ER E THEAT CEIVE IDEO RE AUDIO V 0H R DPL56 T a SURR MODE DIGITAL INPU T DSP MODE LEVEL BASS/TREBLE OK SETUP TEST TONE EQ SOURCE BAND SOURCE TUNING MEMORY ST / MONO V-AUX VIDEO L - AUDIO - R DPL560 l DPL560-EN 4/11/02 5:27 PM Page 4 Safety Information For UK Only CONNECT THE MAIN LEAD INTO A MAINS POWER SOCKET POWER SUPPLY 230V. Note; The mains lead of the set is fitted with a molded plug. If the mains socket are not compatible or if for any reason the plug is removed please follow the directions below. [. . . ] MENU (Tuner Mode only) · Press TUNER · To store Preset Stations. (For details, refer to "Storing and Recalling Stations in Memory" on page 17. ) 8. Operation Buttons · PLAY, RECORD, STOP and PAUSE keys are only for easy control of Thomson DVD player, DVD. The remote control currently operates most Thomson, RCA and GE products. 6 11 9 9. DIGITAL Select the way your audio/video components are connected to the receiver (Analog, Optical or Coaxial). TUNER UP/DOWN In TUNER mode, press TUNER on the remote. · Press TUNER UP and TUNER DOWN keys to tune down or up the radio frequency. 8 11. SURR (Surround Sound Control) Press to change the surround sound settings. The display will toggle among DOLBY DIGITAL, DTS, PRO LOGIC / STEREO. HIFI/DVD Press the appropriate key to control either the receiver or a compatible DVD player (Thomson brand only) Note: After pressing DVD, you must press HIFI to enable all receiver functions on the remote. 11 DPL560-EN 4/11/02 5:27 PM Page 16 Operating Your Receiver Display DTS · Audio output is in DTS mode. SLEEP · Unit in Sleep mode. · Audio output is in Dolby Digital mode. MEMORY · Unit in Memory mode. · Audio output is in Dolby ProLogic mode. ST · Tuner stereo signal detected. KHz MHz RDS · Tuner frequency unit. TUNED · Tuner station detected. L C R · Radio data system is available. LS LFE RS · Speaker Icons. 12 DPL560-EN 4/11/02 5:28 PM Page 17 Operating Your Receiver Switching on/off · To switch on the receiver, press ON/ECO button once, or any source button on the remote control. Selection of Audio/Video source When one of the source buttons is pressed, the audio EN and video input corresponding to the name will be activated. The receiver acts as a switching device between all the sources that are plugged into it. ON/ECO SOURC MUTE SOURC DIGITAL PHONES SOURCE FM/AM SOURCE L TUNING MEMORY · Standby: when the receiver is on, press the ON/ECO button once to activate the standby mode. · To switch off the unit completely, unplug the power cord from the socket Example 1: If you connect a DVD player to the DVD input (audio + video) on the receiver and press the source button repeatedly until DVD is selected, you will be able to have the sound and image transmitted by the DVD. Example 2: SOURCE FM/AM SOURCE L TUNING MEMORY NOTE Your receiver has a back up memory to keep your settings like preset radio station for about 2 weeks in case electricity outage occurs. If the receiver is unplugged for more than 2 weeks, all the settings will be lost and reset to factory settings. Based on the example 1, the DVD is playing , if a VCR is connected to the VCR 1 input (audio + video) of the receiver, press the VCR/VAUX button , or press source button repeatedly until VCR is selected, image and sound from the VCR source will replace the DVD. SOURCE FM/AM SOURCE L TUNING MEMORY 13 DPL560-EN 4/11/02 5:28 PM Page 18 Operating your Receiver You can connect up to 7 audio/video sources to this amplifier: Source button Corresponding connector (receiver front panel) (receiver back panel) DVD SAT VCR VAUX CD TV TAPE FM/AM DVD IN (audio / video) SAT IN (audio / video) VCR IN (audio / video) V-AUX IN (audio / video) CD IN (audio only) TV IN (audio only) TAPE IN (audio only) built-in When a source is selected, the source name will be shown on the display. NOTE 1. Just connect the appropriate antenna on the back of the receiver and you will be able to listen to radio stations. Other sources can be connected to the above standard source. Example: you can connect a LD into the DVD inputs. Refer to the "Connecting To Audio-Visual Components" section for details on connection. 14 DPL560-EN 4/11/02 5:28 PM Page 19 Operating your Receiver Using the receiver to play a source After having properly connected a source (DVD, CD, VCR) to the receiver, you can partly control them through the receiver. EN Playing a DVD with the receiver 1. Connect a DVD player to the receiver (see connecting your receiver for details) NOTE To play Dolby Digital sound / DTS, the source must be connected to the receiver via the optical or coaxial terminal 2. Press ON/ECO to switch on the receiver 3. Switch ON the DVD player and start playback 5. [. . . ] · Make sure the MUTE signal on the front panel is off. · Make sure the digital setting (optical, coaxial or analog) is correct. · Check that the headphone is not inserted. AM TUNER SECTION: Frequency Response: 80Hz ­ 2kHz +/-6dB Usable Sensitivity: 800uV/m @ S/N 20dB Signal to Noise: 38dB Image Ratio: 27dB @ 1000kHz IF Rejection: 35dB FM TUNER SECTION: Frequency Response: 40Hz ­ 15kHz +/-3dB Quieting: 24dBu Signal to Noise: 60dB(stereo) / 65dB(mono) Image Ratio: 40dB IF Rejection: 50dB No audio from one channel. · Check the speaker level setting. · Check the speaker wire or external source cable connections. Dimensions: Unit: 400D x 430W x 130H mm Speaker : 115D x 116W x 175H mm Subwoofer : 355D x 160W x 355H mm Noise occurs when the TV is turned on. · The TV is too close to the audio system. 23 DPL560-EN 4/11/02 5:28 PM Page 28 Care and Maintenance Disconnect the audio system from the power source before performing any maintenance. Headset safety · Do not play your headset at a high volume. [. . . ]