User manual THOMSON DPL680

[. . . ] DPL680 EN 4/8/04 4:00 PM Page 2 ON/EC O THOMSON 46, quai Alphonse Le Gallo 92648 Boulogne Cedex FRANCE 55898990 www. thomson. net DPL680 EN 4/8/04 4:00 PM Page 3 user manual PRESET SURROU SUBWOO FER SOURCE ND VOLUME PHONES AT E THE ST RE SY EM HOM DPL680HT It is important to read this instruction book prior to using your new product for the first time. DPL680 EN 4/8/04 4:00 PM Page 4 Safety Information Rating Information: At bottom / back of the unit this unit comply with the existing requirements In accordance with the rating plate of the unit, this unit complies with current standards concerning electrical safety and electromagnetic compatibility. Please respect the environment Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling. Have a Blast- Just Not in Your Eardrums Make sure you turn down the volume on the unit before you put on headphones. Increase the volume to the desired level only after headphone are in place. THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WA R N I N G S I G N ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] + / - (Volume Buttons) Adjusts the volume level. CH+ / CH- (Channel Buttons) Selects programmed stations in TUNER mode. Changes chapter when the source is in DVD. Changes Station or Channel when the source is in TV or Satellite. 15. Operation Buttons In TUNER mode: · Press the TUNER - and TUNER + keys to tune down or up the radio frequency. · Press SAVE to activate the preset station saving and press to confirm preset station settings. · PLAY, RECORD, STOP and PAUSE keys are only for easy control of external devices that are connected to your receiver such as CD, VCR, DVD, TAPE, etc. . The remote control currently operates most Thomson products. NOTE The remote control button CLEAR, MENU and GUIDE do not function for this receiver but can be used to control other Thomson products. 11 DPL680 EN 4/8/04 4:01 PM Page 16 Operating Your Receiver Display C R S RS DVD / VCR / SAT / TUNER / TAPE / CD / TV · An arrow points to the current source mode. TUNED · Tuner station detected. L C R · Dolby Digital audio input for signal format. LS LFE RS · Dolby Pro Logic II audio output format. · Speaker Icons. L - Front left speaker C - Center speaker R - Front right speaker LS - Left surround (rear) speaker RS - Right surround (rear) speaker LFE - Subwoofer speaker · DTS audio output format. SLEEP · Unit in Sleep mode. FM / AM · Radio band indicator in Tuner mode. MEMORY · Unit is ready to store a station in selected preset. ST · Tuner stereo signal selected. RDS · Radio data system information is received. OPT 1 2 · Optical digital input selected. KHz / MHz · Tuner frequency unit. COAX · Coaxial digital input selected. 12 DPL680 EN 4/8/04 4:01 PM Page 17 Operating Your Receiver Switching the unit on and off · To switch on the receiver, press the ON/ECO button on the main unit once, or the button on the remote control. Example 1: If you have connected a DVD player to the DVD input (audio & video) on the receiver, press the SOURCE button on the main unit repeatedly until DVD is selected or press DVD·6CH on the remote control to receive the sounds and images transmitted by the DVD. EN ON/ECO SUBWOOFER SOURCE SURROUND · Standby: when the receiver is in tuner mode, press the ON/ECO button once to enter standby mode. On the remote control, press the button twice within 2 seconds if the receiver is not in Tuner source mode to enter standby mode. To avoid entering standby mode when powering up the unit, do not press the button twice within 2 seconds. · The receiver draws a small amount of electricity when in standby mode. Unplugging the unit from the wall socket will stop the draw. Example 2: Based on the example 1, the DVD is playing , if a VCR is connected to the VCR input (audio & video) of the receiver, press the SOURCE button on the main unit repeatedly until VCR is selected or press AUX 1 (VCR) on the remote control. The image and sound from the VCR source will replace the DVD. SUBWOOFER SOURCE SURROUND Selection of Audio/Video source When one of the source buttons is pressed, the audio and video input corresponding to the name will be activated. The receiver acts as a switching device between all the sources that are plugged into it. SUBWOOFER SOURCE SURROUND 13 DPL680 EN 4/8/04 4:01 PM Page 18 Operating your Receiver You can connect up to 6 audio/video sources to this amplifier: Source button (receiver front panel) DVD VCR SAT CD TAPE TV FM/AM Corresponding connector (receiver back panel) DVD IN (audio / video) VCR IN/OUT (audio / video) SAT IN (audio / video) CD IN (audio only) TAPE IN/OUT (audio only) TV IN (audio only) built-in NOTE The remote control can only operate Thomson brand products. Volume Punchthrough NOTE Volume punchthrough can be done in all non-Tuner modes. By default, the VOL+/VOL- and MUTE buttons will only control the receiver, regardless which mode (TV, VCR, etc) the receiver is in. By programming the volume punchthrough function, you can also control the volume of the TV. An arrow points to the source name selected shown on the display. Example : If you have connected a DVD player to the DVD input (audio & video) on the receiver, press the SOURCE button on the main unit repeatedly until DVD is selected or press DVD·6CH on the remote control to receive the sounds and images transmitted by the DVD. NOTE 1. Just connect the appropriate antenna to the back of the receiver and you will be able to listen to radio stations. Other sources can be connected to the above standard source. Example: you can connect a LD into the DVD inputs. [. . . ] Be sure to match the + and - ends of each battery to the symbols shown in the remote battery compartment. · The remote is not pointed at the remote control sensor on the main unit or there is an obstacle between the remote and the main unit. · The remote control is too far from the main unit, move closer. Specific instruments sound displaced. · Check the connections between the receiver and the speakers if the sound does not match the video. · Check if the video and audio cable are correctly inserted. TAPE OUT and REC OUT do not operate in VCR mode. · Check to make sure analog input signal is connected from the signal source to the analog input jacks. [. . . ]