User manual THOMSON DTH6000

[. . . ] Contents Installation Precautions and guarantee . . 4 Basic connection - Other connection possibilities DVD Mode Play . . 22 Simple play - Accelerated play - Still image / Frame advance - Variable slow motion - Zoom function EN Other devices . . 6 General functions - Functions in DVD mode Functions in VCR mode Play Modes . [. . . ] Display the OVERVIEW menu using the MENU key. Select the Record timer line using the w key. Confirm with OK. The TIMER menu comes up. 4 Use the number keys to enter the channel number, 5 the PR+/- key to select the channel or the AV key to 31/12 No select the corresponding AV socket if you want to Once SP record a satellite and/or encoded programme. 0000 Clear Type in the following information by selecting the VCR corresponding line using the w key: start time of the programme, end time of the programme and the date, if the recording is not to take place on the same day. You can also complete your programming by selecting the following options: recording triggered by VPS or PDC signals, frequency (Once, Mon-Fri, Weekly), speed (SP or LP). Long Play recording enables you to record up to twice the length of the tape. TIMER Prog. number Start Stop Date VPS/PDC Frequency Speed Timer review 0-9 : Select CB - - - - - - 5 --:---:-- 6 Switch the video recorder on STANDBY using the B key. The indication appears on the display of your video recorder to tell you that your programming was successful. A great number of satellite receivers, including all digital models, need to be left on to properly perform timer-programmed recordings. To check your programming 1 2 3 4 Press the MENU key to call up the OVERVIEW menu. Select the Record timer line using the w key and validate with OK. Select the Timer review line and press OK. The eight possible recordings are spread over 2 pages. To view page 2, select Next page using w and then press OK. Error messages likely to occur when programming NO TIMER AVAILABLE If all timers are already used, you need to clear one timer using the 0000 key before trying again to programme your recording. 17 Use TIMER OVERLAP If you programme two or more recordings with overlapping time periods, the TIMER menu comes up along with an error message and the overlapping programmed recordings are flashing. Delete the programmed recordings using the 0000 key. REVIEW INCOMPLETE TIMER Check that you have completed all the requirements for the recording (start and end times, etc. ). Deleting a programmed recording 1 Display the OVERVIEW menu using the MENU key, select the Record timer line with 2 3 4 the w key and confirm with OK. Select the Timer review line and press OK. Select the programming you wish to delete using the w and v keys. Leave the menu using the EXIT key. Recording programmed on a connected set The recording of a programme can be triggered by a satellite receiver or another device designed for this purpose connected to socket AV1 or AV2 with a SCART cable. This avoids having to programme both units. Programme the connected device and select AV1 or AV2 as appropriate in the video recorder's TIMER menu. 18 Use Sound control Sound selection in playback mode 3 4 the w key. Using the C or B key, select the sound tracks. - Stereo: stereo sound of the Hi-Fi tracks, - Mono: mono sound of the linear track, - Track 1: sound of the left track Sound mode B Stereo - Track 2: sound of the right track, - Mix: sound of the mixed Hi-Fi and mono tracks. If the tape was recorded in Dolby Surround or Dolby Pro Logic Surround, connection of a special audio/video amplifier will allow you to reproduce these sound effects. "DOLBY", "Prologic" and the double-D symbol Laboratories Licensing Corporation. VCR 1 Load a tape and press PLAY. 2 Call the OVERVIEW menu using the MENU key and select the Sound mode line using EN VCR are trademarks of DOLBY Setting the type of sound to be recorded The broadcast sound types are different from channel to channel. Your video recorder uses 3 tracks to record the sound: - two HiFi tracks for stereo or bilingual sound (track 1 and 2), - one normal track for mono sound or track 1 for a bilingual telecast. Depending on the actual sound type of the TV channel (stereo, NICAM or mono), the video recorder will distribute the sound on these different tracks. Display the OVERVIEW menu using the MENU key, then select the Sound mode line 1 2 with w. 3 Confirm with OK. The SOUND MODE menu comes up. 4 Select the Stereo, Mono, Track 1 or Track 2. Sound mode B Mono VCR 19 Use Preferences 1 Display the OVERVIEW menu using the MENU key, then 2 3 select the Preferences line using the w key. [. . . ] Check that the DVD disc provides subtitles. 29 27 Disc menu language The disc menu language is not the 1. The disc menu language has not been set up. The language of your choice is not available on the disc. Lock You have forgotten your password. [. . . ]