User manual THOMSON DTI 1000

[. . . ] 3569723D DTI1000 UM8. qxp 02/03/2005 12:23 Page 1 User manual 3569723D DTI1000 UM8. qxp 02/03/2005 12:24 Page 2 Set-up Contents 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Accessories Safety Information Connections Remote Control Handset Tuning the Receiver Advanced Setup Program Information Lists and interactive services Timer Programming and Recording Parental Controls Upgrading your Receiver Other Information Trouble Shooting and Information Your Guarantee Accessories Operation Manual 2 x AA batteries Guarantee Card DTI1000 Power Cord Remote Control Scart Lead 2 3569723D DTI1000 UM8. qxp 02/03/2005 12:24 Page 3 Set-up Introduction Congratulations on your choice of this state-of-the-art Digital Free to View Receiver. We hope you will enjoy all the new features this technology brings to your home for many years. Your dealer should have checked your postcode for reception, but the availability of Digital Signals does depend on the transmitter(s) available to your receiving aerial. If you have any doubt about this availability, please contact your dealer, or check the following internet websites:www. freeview. co. uk or www. dtg. org. uk/consumer If you experience reception problems contact our aerial helpline on 0800 5428265 Safety information In order that you may enjoy this product for a long time it is important that you observe the following points when installing and operating your receiver This receiver is intended for the reception of TV picture and sound signals. [. . . ] Press [MENU], select SERVICE LIST and press [OK]. To delete the selected service, press [RED]. (Once deleted, you must repeat manual/auto tune to view) 4. To add a service to the Favourite List, select the service and then press [BLUE] until "YES" is shown. To remove a service from the Favourite List press [BLUE] until "NO" is shown. Press [OK] to view the selected service. Favourite List All Free-to-View services are automatically set to favourites after a Manual or Auto tune. This list determines the order in which services are selected when using the Pr+/Pr- keys. So for the example below, when watching five, pressing Pr+ would select BBC Radio 2. Press [MENU], select FAVOURITE LIST and press [OK]. Select the service you wish to move with / and press [BLUE]. (The service will be highlighted in red) / 3. Now move the service using to your desired location and press [BLUE] to store it in position. Repeat this process until the list is how you wish it. The favourite channels are now set to suit your personal requirements. To view channels that are not selected as favourites, use TV Guide, Service List or enter the channel number directly via the remote control, 0. . 9. Teletext and interactive services If your chosen channel has Teletext (MHEG) features use [TEXT] to access them. To return to normal viewing press [TEXT] again. When the Timer Event has been activated, both RED and GREEN LEDs will be lit for the duration of the event. A suitably equipped VCR will record automatically during this time. Please note that unless your VCR supports automatic scart recording YOU MUST ALSO SET THE VCR TIMER. In order to delete an entry you no longer need, position the cursor over the entry to be removed in the TIMER PROGRAMMING menu and press [RED]. Cancel an event at any time by pressing [QUIT]. Press [QUIT] again to confirm. 10 3569723D DTI1000 UM8. qxp 02/03/2005 12:24 Page 11 Use Parental controls You can use PARENTAL CONTROL to create viewing restrictions on your receiver. [. . . ] If the mains sockets are not compatible or if for any reason the plug is removed please follow the directions below. The moulded plug cannot be rewired and if removed must be disposed of safely. Do NOT under any circumstances plug the severed plug into any mains socket as this could result in an electric shock. If the plug is removed, rewire new plug as follows: The wires in the mains plug are coloured in accordance with the following code: BLUE - NEUTRAL BROWN - LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: BLUE wire to the terminal coded N (Neutral) or coloured black. [. . . ]