User manual THOMSON IFC130 CODES

[. . . ] Do not cover the vents at the back or sides of the TV set. Leave sufficient space around it to allow adequate ventilation. Install the appliance away from any source of heat (fireplace, . . . ) or appliances creating strong magnetic or electric fields. Moisture in rooms where the set is installed should not exceed 85% humidity. [. . . ] In PIP mode, press the FREEZE or OK button to freeze the picture of the main programme. Flat batteries When the batteries are flat a message appears on the screen when you press a button on the remote control. You should change the batteries and reprogram the remote control (see page 5). 10 IFC130-plasma_EN 5/07/04 13:26 Page 11 Advanced functions Adjusting the sound Display the OVERVIEW menu by pressing the MENU button. Select the Sound option and press OK to confirm. Return Sound type Sound mode Automatic sound level Dynamic Bass Headphone settings Graphic equaliser Other settings Stereo. . . . . . The Sound menu appears with the following options: Sound type: select a sound type from the list using the buttons. The default sound type is Automatic for mono sources, Stereo for stereo sources and Stereo for AV sources. Note: The options offered depend on the programme you're watching. Refer to the table opposite. Sound Sound mode:The options available depend on the sound type selected. Note: Magic and Dolby Virtual modes are only available for stereo audio sources. EN Broadcast Mono Stereo Dual NICAM - 3 Analog AV Sound type Mono Stereo Sound 1 Sound 2 Sound types Automatic - Mono Mono - Stereo Sound 1 - Sound 2 Sound 1 - Sound 2 Sound 3 Stereo - Sound 1 - Sound 2 Automatic sound level: check the box by pressing the OK button, if you want to keep the same sound level for all channels. Dynamic Bass: this function is used to strengthen the bass. Select an option from the list using the further below). buttons. Headphone settings: this option allows access to the headphone setting menu (see Graphic equaliser: this option allows access to the graphic equaliser (see further Sound modes Normal - Wide Normal - Magic Dolby Virtual Normal - Wide Normal - Wide below). Other settings: see further below. Press EXIT to close the menu. Select RETURN and press OK to return to the OVERVIEW menu. Headphone settings Return Headphone volume Headphone bass Headphone treble Headphone sound HP set Select the Headphone settings option from the Sound menu and press OK to display the menu. Then select each option in turn, using the buttons to adjust the volume, bass and treble levels. Stereo. . . Headphone sound: select a sound type from the list using the buttons. The default sound type is Automatic for mono sources, Stereo for stereo sources and Stereo for AV sources. Press EXIT to close the menu. To return to the Sound menu, select Return and press OK to confirm. Graphic equaliser Return Equalizer Sound preset Film. . . Select Graphic equaliser from the Sound menu and press OK to display the menu. This menu is used to select a preset parameter and define your own settings using the graphic equaliser. Select an option from the list using the buttons: - Off: function disabled, - On: detection, - Advanced: detection, then enhancement of picture quality. Notes: - The Advanced option is selected by default. - This function is only available for certain audio-visual sources. PC mode - Full screen and Single Tint: is used to adjust the picture's tint. Note: This function is only available for NTSC audio-visual sources. Auto skin tone: improves skin tone rendering. Check the box to enable this function by pressing OK. Note: This function is only available for NTSC audio-visual sources. Auto-adjustment: this function is used to automatically adjust the Phase and Clock functions. Press OK to start the adjustment process and wait until Done appears. Phase, Clock: adjust these settings as required in order to enhance picture quality. Horizontal position: use the buttons to move the picture horizontally on the screen. Vertical position: use the buttons to move the picture vertically on the screen. Press EXIT to close the menu. To return to the Picture menu, select Return and press OK to confirm. 13 IFC130-plasma_EN 5/07/04 13:26 Page 14 Advanced functions Setting the time The Time menu can be used to set the time on the TV set and program the automatic sleep timer or wake-up timer functions. Return Time EN Sleep timer 00:15 Clock reference programme 02 Time and date 12:34 03/03/03 Wake-up timer Wake-up time 07:00 Switch on for 01:00 Programme number 10 CNN Daily Display the OVERVIEW menu by pressing the MENU button. Select the Time option and press OK to confirm. Setting the time 1. Select the Clock reference programme option. Select a channel with Teletext which can provide the time to be used as a reference using the buttons, or enter a channel number using the numeric buttons on the remote control. The time is displayed after a few seconds if it is available on the selected channel. If the time is not provided by Teletext the Wake-up timer function is not available and a message prompts you to change reference channel or enter the time manually. You do this by selecting the Time and date option and entering the time using the numeric buttons or the buttons. Note: If the power supply is disrupted (i. e. [. . . ] Select RECORD from the navigator and press OK to confirm. The programme is then added to the recording list. Notes: - This function is only useful if you have a video recorder which has the NexTView Link function and is connected to an AV1 socket. In this case, the television will automatically programme the video recorder. - The instructions for use are the same as those given in the paragraph "Recording a programme" on the previous page. To select a programme in the list, use the ¦ keys. Memo: can be used to store a programme from the recording list in the memo list. 1. Select the programme you wish to store from the recording list. [. . . ]